Infiniti Q45. Manual — part 701
INTERIOR ROOM LAMP
LT-141
C
D
E
F
G
H
I
J
L
M
A
B
LT
Key Switch and Key Lock Solenoid System Check
NKS001A3
1.
CHECK KEY SWITCH AND KEY LOCK SOLENOID SIGNAL
With CONSULT-II
●
Insert and withdrawn the key via “IGN KEY SW” on DATA MON-
ITOR screen and make sure that switch turns on and off accord-
ingly.
Without CONSULT-II
●
Check voltage between BCM connector M4 terminal 69 and
ground while inserting and withdrawn the key.
OK or NG
OK
>> Key switch and key lock solenoid is OK.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and key switch connector.
3.
Check continuity between BCM harness connector M4 terminal
69 and key switch and key lock solenoid harness connector M64
terminal 4.
4.
Check continuity between BCM harness connector M4 terminal
69 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
SKIA0445E
Key withdrawn (switch OFF)
: Approx. 0 V
Key inserted (switch ON)
: Battery voltage
PKIA7711E
69 - 4
: Continuity should exist.
69 - Ground
: Continuity should not exist.
PKIA5158E
LT-142
INTERIOR ROOM LAMP
3.
CHECK KEY SWITCH AND KEY LOCK SOLENOID
Check continuity between key switch and key lock solenoid termi-
nals 3 and 4 while inserting and withdrawing the ignition key.
OK or NG
OK
>> GO TO 4.
NG
>> Replace key switch and key lock solenoid.
4.
CHECK POWER SUPPLY CIRCUIT
Check voltage between key switch and key lock solenoid harness
connector M64 terminal 3 and ground.
OK or NG
OK
>> Key switch and key lock solenoid is OK.
NG
>> Check harness for open and short between key switch
and key lock solenoid and fuse.
Key withdrawn
(switch OFF)
: Continuity should not exist.
Key inserted
(switch ON)
: Continuity should exist.
PKIB4117E
3 - Ground
: Battery voltage
PKIA5160E
INTERIOR ROOM LAMP
LT-143
C
D
E
F
G
H
I
J
L
M
A
B
LT
Bulb Replacement
NKS001A4
MAP LAMP (FRONT PERSONAL LIGHT) AND CONSOLE LAMP (CONSOLE LIGHT)
Map Lamp
1.
Remove finisher using a clip driver or a suitable tool.
2.
Insert a thin screwdriver in the notch and remove lens.
3.
Remove screw and remove shade.
4.
Remove bulb.
Console Lamp
1.
Remove front interior lamp. Refer to
.
2.
Turn console lamp bulb socket counterclockwise and unlock it.
PERSONAL LAMP (REAR PERSONAL LIGHT)
1.
Remove rear interior lamp. Refer to
2.
Unfold the tabs and remove lens.
3.
Remove shade mounting screw and remove shade from per-
sonal lamp.
4.
Remove bulb.
Removal and Installation
NKS001A5
FRONT INTERIOR LAMP
1.
Open front interior lamp box and remove screw.
2.
Insert a clip driver or a suitable tool and disengage the metal clip
fittings of front interior lamp.
3.
Disconnect connector and remove front interior lamp.
REAR INTERIOR LAMP
1.
Using a clip driver or a suitable tool, press and remove metal clip
of rear interior lamp.
2.
Disconnect rear interior lamp connector.
Map lamp (Front personal light)
: 12V - 8W
PKIA0177E
Console lamp (Console light)
: 12V - 1.4W
Personal lamp (Rear personal light)
: 12V - 8W
PKIA0073E
PKIA0068E
PKIA0074E
LT-144
INTERIOR ROOM LAMP
IGNITION KEY HOLE ILLUMINATION
1.
Remove lower instrument panel (driver side). Refer to
.
2.
Turn bulb socket counterclockwise and unlock it.
Ignition key hole illumination
: 12V - 1.4W
PKIA0187E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст