Infiniti Q45. Manual — part 202
REMOTE KEYLESS ENTRY SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
M
A
B
BL
Malfunction Code Table
NOTE:
●
For a specific local control unit (LCU), either “PAST COMM DATA” or “PAST NO RESPONSE” may be displayed instead of the
above results. This is caused by the data record, so erase the records.
(The display only shows the incident records, they are not malfunctions caused during the diagnosis. One possible cause is that an
reproducible incident occurred.)
●
Follow the steps below to erase the memory
Perform either disconnect BCM battery power supply or erase memory with CONSULT-II.
●
With the battery connected, if the local control unit (LCU) connector is disconnected and left for approximately 1 minute, the BCM
stores “NO RESPONSE” record.
DATA MONITOR
Remote Keyless Entry Item
Malfunctioning item
Display unit
CONSULT-II IVMS communication diag-
nosis content
Self-diagnosis
trouble code
No.
Malfunctioning system and
reference
COMM DATA
One LCU is dis-
played.
POWER WINDOW C/U-DR
“COMM DATA”
24
Replace the displayed
LCU.
DOOR MIRROR C/U-RH
“COMM DATA”
27
DOOR MIRROR C/U-LH
“COMM DATA”
37
POWER SEAT C/U-DR
“COMM DATA”
47
Multiple LCUs
are displayed.
BCM
“COMM FAIL1”, “COMM FAIL2”
Displays in
order of 24
→
27
→
37
→
47
→
and cycles
from 24.
Communication system A:
Refer to
NO
RESPONSE
One LCU is dis-
played.
POWER WINDOW C/U-DR
“NO RESPONSE”
25
Communication system B:
Refer to
DOOR MIRROR C/U-RH
“NO RESPONSE”
28
DOOR MIRROR C/U-LH
“NO RESPONSE”
38
POWER SEAT C/U-DR
“NO RESPONSE”
48
Multiple LCUs
are displayed.
BCM/HARNESS
Displays in
order of
25
→
28
→
38
→
4
8 and cycles
from 25.
Communication system C:
Refer to
.
SLEEP malfunction
One LCU is dis-
played.
POWER WINDOW C/U-DR
“SLEEP”
No self-diagno-
sis function
Replace the displayed
LCU.
DOOR MIRROR C/U-RH
“SLEEP”
DOOR MIRROR C/U-LH
“SLEEP”
POWER SEAT C/U-DR
“SLEEP”
Multiple LCUs
are displayed.
All the above control units are displayed.
No self-diagno-
sis function
Communication system A:
Refer to
Monitored item
Description
IGN KEY SW
Indicates [ON/OFF] condition of ignition key switch.
IGN ACC SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
BL-78
REMOTE KEYLESS ENTRY SYSTEM
Trunk Lid Opener Item
ACTIVE TEST
Remote Keyless Entry Test Item
Trunk Lid Opener Test Item
WORK SUPPORT
Work Support Item
Hazard and Horn Reminder mode
*: These modes are not supported.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
LOCK SIG-DR
Indicates [ON/OFF] condition of driver door unlock signal from door unlock sensor.
LOCK SIG-AS
Indicates [ON/OFF] condition of passenger door unlock signal from door unlock sensor.
LOCK SIG-RR/RH
Indicates [ON/OFF] condition of rear RH door unlock signal from door unlock sensor.
LOCK SIG-RR/LH
Indicates [ON/OFF] condition of rear LH door unlock signal from door unlock sensor.
LOCK BUTTON
Indicates [ON/OFF] condition of lock signal from electronic key.
UNLOCK BUTTON
Indicates [ON/OFF] condition of unlock signal from electronic key.
PANIC BTN
Indicates [ON/OFF] condition of panic signal from electronic key.
TRUNK BTN-CON
Indicates [ON/OFF] condition of trunk open signal from electronic key.
Monitored item
Description
Monitored item
Description
TRUNK OPNR SW
Indicates [ON/OFF] condition of trunk open signal from trunk open switch.
TEST ITEM
DESCRIPTION
TRUNK OPEN S/V
This test is able to check trunk lid opener actuator operation.
The trunk is unlocked when “ON” on CONSULT-II screen is touched.
HAZARD
This test is able to check hazard reminder operation.
The hazard lamp turns on when “ON” on CONSULT-II screen is touched.
HORN
This test is able to check panic alarm and horn reminder operations.
The horn turns on when “ON” on CONSULT-II screen is touched.
FOOT ILL
This is displayed even when it is not equipped.
TEST ITEM
DESCRIPTION
TRUNK OPEN S/V
This test is able to check trunk lid opener actuator operation.
The trunk is unlocked when “ON” on CONSULT-II screen is touched.
WORK ITEM
DESCRIPTION
KYLS OP CONF SET
Hazard and horn reminder mode can be changed in this mode. (NORMAL or MODE1)
KYLS ID P/W SET
Keyless power window down (open) operation mode can be changed in this mode. (ON or OFF)
REMO CONT ID CONFIR
It can be checked whether electronic key ID code is registered or not in this mode.
REMO CONT ID REG
electronic key ID code can be registered in this mode.
REMO CONT ID ERASER
electronic key ID code can be erased in this mode.
NORMAL
MODE1
MODE2*
MODE3*
MODE4*
MODE5*
Electronic key operation
Lock
Unlock
Lock
Unlock
—
—
—
—
Hazard warning lamp flash
Twice
Once
Twice
–
Horn sound
Once
–
–
–
REMOTE KEYLESS ENTRY SYSTEM
BL-79
C
D
E
F
G
H
J
K
L
M
A
B
BL
On Board Diagnosis
NIS000UN
ON BOARD DIAGNOSTIC RESULTS INDICATOR LAMP
●
Map lamps and step lamps (all seats) act as the indicators for the on board diagnosis.
DIAGNOSIS ITEM
COMMUNICATION DIAGNOSIS
Check the communication between BCM and local control unit (LCU).
How To Perform Communication Diagnosis
Description
In this mode, a malfunction code is indicated by the number of flashes from the map lamps and step lamps as
shown below:
After indicator lamp turns on for 2 seconds then off for 2 seconds, it flashes [cycling ON (0.5 sec.)/OFF (0.5
sec.)] to indicate a malfunction code of the first digit. Then, 1.5 second after indicator lamp turns off, it again
flashes [cycling ON (0.5 sec.)/OFF (0.5 sec.)] to indicate a malfunction code of the second digit.
For example, the indicator lamp goes on and off for 0.5 seconds twice and after 1.5 seconds, it goes on and off
for 0.5 seconds four times. This indicates malfunction code of driver door control unit communication.
Diagnosis item.
Content
IVMS communication diagnosis
Diagnosing any abnormality or inability of communication between BCM and LCU
(DATA LINE A-3).
Switch monitor
Monitoring conditions of switches connected to BCM, LCU and Door control unit.
PIIA3358E
SIIA0410E
BL-80
REMOTE KEYLESS ENTRY SYSTEM
Malfunction Code Table
NOTE:
●
For a specific local control unit (LCU), either “PAST COMM DATA” or “PAST NO RESPONSE” may be displayed instead of the
above results. This is caused by the data record, so erase the records.
(The display only shows the incident records, they are not malfunctions caused during the diagnosis. One possible cause is that an
reproducible incident occurred.)
●
Follow the steps below to erase the memory
Perform either disconnect BCM battery power supply or erase memory with CONSULT-II.
●
With the battery connected, if the local control unit (LCU) connector is disconnected and left for approximately 1 minute, the BCM
stores “NO RESPONSE” record.
Cancel of Communication Diagnosis
If one of the following conditions is satisfied, the communication diagnosis is cancelled.
●
Turn ignition switch OFF.
●
Drive the vehicle more than 7 km/h (4 MPH).
●
Ten minutes have passed since the diagnosis result indication start without any diagnosis cancel opera-
tion.
Malfunction item
Display unit
CONSULT-II IVMS communication diag-
nosis content
Self-diagnosis
trouble code
No.
Malfunctioning system and
reference
COMM DATA
One LCU is dis-
played.
POWER WINDOW C/U-DR
“COMM DATA”
24
Replace the displayed
LCU.
DOOR MIRROR C/U-RH
“COMM DATA”
27
DOOR MIRROR C/U-LH
“COMM DATA”
37
POWER SEAT C/U-DR
“COMM DATA”
47
Multiple LCUs
are displayed.
BCM
“COMM FAIL1”, “COMM FAIL2”
Displays in
order of 24
→
27
→
37
→
47
→
and cycles
from 24.
Communication system A:
Refer to
NO
RESPONSE
One LCU is dis-
played.
POWER WINDOW C/U-DR
“NO RESPONSE”
25
Communication system B:
Refer to
DOOR MIRROR C/U-RH
“NO RESPONSE”
28
DOOR MIRROR C/U-LH
“NO RESPONSE”
38
POWER SEAT C/U-DR
“NO RESPONSE”
48
Multiple LCUs
are displayed.
BCM/HARNESS
Displays in
order of
25
→
28
→
38
→
4
8 and cycles
from 25.
Communication system C:
Refer to
SLEEP malfunc-
tion
One LCU is dis-
played.
POWER WINDOW C/U-DR “SLEEP”
No self-diagno-
sis function
Replace the displayed
LCU.
DOOR MIRROR C/U-RH
“SLEEP”
DOOR MIRROR C/U-LH
“SLEEP”
POWER SEAT C/U-DR
“SLEEP”
Multiple LCUs
are displayed.
All the above control units are displayed.
No self-diagno-
sis function
Communication system A:
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст