Infiniti G37 Coupe. Manual — part 1376
SUNLOAD SENSOR
VTL-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SUNLOAD SENSOR
Exploded View
INFOID:0000000001665933
Removal and Installation
INFOID:0000000001665934
REMOVAL
1.
Remove front defroster grille (left). Refer to
.
2.
Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
1.
Sunload sensor
JSIIA0218ZZ
JSIIA0050ZZ
VTL-28
< ON-VEHICLE REPAIR >
INTAKE SENSOR
INTAKE SENSOR
Exploded View
INFOID:0000000001713720
1.
Aspirator
2.
Aspirator hose
3.
Front heater duct
4.
Foot duct (left)
5.
Defroster seal
6.
Packing
7.
Ventilator seal
8.
Ventilator door
9.
Foot duct (right)
10. Defroster door lever
11.
Foot door lever
12.
Ventilator door lever
13. Ventilator door link
14.
Main link
15.
Mode door motor bracket
16. Mode door motor
17.
Air mix door motor (passenger side)
18.
Intake sensor
19. Intake sensor bracket
20.
O-ring
21.
Low-pressure pipe 1
22. High-pressure pipe 2
23.
Expansion valve
24.
Cooler pipe grommet
25. Insulator
26.
Evaporator cover adapter
27.
Heater pipe bracket
28. Case rubber
29.
Case packing
30.
Heater & cooling unit case (left)
31. Heater pipe grommet
32.
Heater core
33.
Air mix door motor (driver side)
*
34. Foot door (left)
35.
Rear ventilator door
36.
Foot door (right)
JSIIA0863GB
INTAKE SENSOR
VTL-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
Removal and Installation
INFOID:0000000001665936
REMOVAL
1.
Remove low-pressure pipe 1 and high-pressure pipe 2. Refer to
CAUTION:
Cap or wrap the joint of the A/C piping with suitable material such as vinyl tape to avoid the entry
of air.
2.
Slide evaporator (1) to passenger side, and then remove intake
sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• Check for leakages when recharging refrigerant.
37.
Max. cool door lever
38.
Foot door link
39. Defroster door link
40.
Max. cool door link
41.
Main link sub
42. Evaporator cover
43.
Heater & cooling unit case (right)
44.
Evaporator
45. Drain hose
46.
Clamp
47.
Air mix door (Slide door)
48. Air mix door adapter
49.
Heater pipe cover
50.
Max. cool door (left)
51. Defroster door (left)
52.
Center case
53.
Defroster door (right)
54. Max. cool door (right)
*
With left and right ventilation temperature separately system.
Refer to
for symbols in the figure.
JSIIA0052ZZ
VTL-30
< ON-VEHICLE REPAIR >
BLOWER UNIT
BLOWER UNIT
Exploded View
INFOID:0000000001665937
Removal and Installation
INFOID:0000000001665938
REMOVAL
1.
Remove instrument lower panel. Refer to
.
2.
Disconnect ECM (1) connectors.
3.
Remove mounting nuts (A), and then remove ECM with bracket
attached.
4.
Remove power steering control unit. Refer to
5.
Disconnect intake door motor (2) connector and blower motor
(3) connector.
6.
Remove mounting bolt (B) and screw (C), from blower unit (4).
7.
Remove blower unit.
CAUTION:
Move blower unit rightward, and remove locating pin (1
part) and joint. Then remove blower unit downward.
INSTALLATION
Installation is basically the reverse order of removal.
1.
Adapter
2.
Intake box (right)
3.
Intake door lever 2
4.
Intake door motor
5.
Intake door link
6.
Intake door lever 1
7.
Filter cover
8.
In-cabin microfilter
9.
Intake upper case
10. Intake lower case
11.
Blower motor assembly
12. Seal
13. Intake box (left)
14.
Intake door 1
15. Intake door 2
JSIIA0009ZZ
JSIIA0855ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст