Infiniti G37 Coupe. Manual — part 922
MWI-34
< FUNCTION DIAGNOSIS >
CLOCK
CLOCK
Component Parts Location
INFOID:0000000001606645
1
: Clock
JSNIA0038GB
MWI
DIAGNOSIS SYSTEM (METER)
MWI-35
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (METER)
Diagnosis Description
INFOID:0000000001606646
SELF-DIAGNOSIS MODE
• Information display LCD segment operation can be checked in self-diagnosis mode.
• Meters/gauges can be checked in self-diagnosis mode.
OPERATION PROCEDURE
1.
Turn ignition switch ON, and switch the trip meter to “trip A” or “trip B”.
NOTE:
If the diagnosis function is activated with “trip A” displayed, the mileage on “trip A” is reset to “0000.0”.
(The same way for “trip B”.)
2.
Turn ignition switch OFF.
3.
While pressing the trip A/B reset switch (1), turn ignition switch
ON again.
4.
Make sure that the trip meter displays “0000.0”.
5.
Press the trip A/B reset switch at least 3 times. (Within 7 sec-
onds after the ignition switch is turned ON.)
6.
The unified meter control unit is turned to self-diagnosis mode.
• Displays "888888" (1) and "8888.8" (2) in the information display LCD (3) for approximately 5 seconds
and then blinks the segment dots of the information display LCD alternately.
• Water temperature gauge and fuel gauge return to zero, and at the same time.
NOTE:
• Check tirp A/B reset switch and combination meter power supply and ground circuit when self-diagnosis
mode of combination meter does not start. Replace combination meter if they are normal.
• If any of the segments is not displayed, replace combination meter.
JSNIA0019GB
JSNIA0616GB
MWI-36
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (METER)
7.
Each meter activates during pressing trip A/B reset switch.
NOTE:
If any of the meter and gages is not activated, replace combination meter.
JSNIA0021GB
MWI
DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.)
MWI-37
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (UNIFIED METER AND A/C AMP.)
CONSULT-III Function (METER/M&A)
INFOID:0000000001606647
CONSULT-III APPLICATION ITEMS
CONSULT-III can perform the following diagnosis modes with CAN communication with the unified meter and
A/C amp.
SELF DIAG RESULT
DATA MONITOR
Display Item List
X: Applicable
System
Diagnosis mode
Description
METER/M&A
Self Diagnostic Result
Unified meter and A/C amp. checks the conditions and displays memorized error.
Data Monitor
Displays unified meter and A/C amp. input/output data in real time.
Display item [Unit]
MAIN
SIGNALS
Description
SPEED METER
[km/h]
X
Value of vehicle speed signal received from ABS actuator and electric unit (control
unit) with CAN communication line.
NOTE:
655.35 is displayed when the malfunction signal is received.
SPEED OUTPUT
[km/h]
X
Vehicle speed signal value transmitted to other units with CAN communication
line.
NOTE:
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
[km]
Odometer signal value transmitted to other units with CAN communication line.
TACHO METER
[rpm]
X
Value of the engine speed signal received from ECM with CAN communication
line.
NOTE:
8191.875 is displayed when the malfunction signal is received.
FUEL METER
[L]
X
Fuel level indicated on combination meter.
W TEMP METER
[
°
C]
X
Value of engine coolant temperature signal received from ECM with CAN commu-
nication line.
NOTE:
215 is displayed when the malfunction signal is input.
ABS W/L
[On/Off]
Status of ABS warning lamp judged from ABS warning lamp signal received from
ABS actuator and electric unit (control unit) with CAN communication line.
VDC/TCS IND
[On/Off]
Status of VDC OFF indicator lamp judged from VDC OFF indicator lamp signal re-
ceived from ABS actuator and electric unit (control unit) with CAN communication
line.
SLIP IND
[On/Off]
Status of SLIP indicator lamp judged from slip indicator lamp signal received from
ABS actuator and electric unit (control unit) with CAN communication line.
BRAKE W/L
[On/Off]
Status of brake warning lamp judged from brake warning lamp signal received
from ABS actuator and electric unit (control unit) with CAN communication line.
NOTE:
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L
[On/Off]
Status of door warning judged from door switch signal received from BCM with
CAN communication line.
TRUNK/GLAS-H
[On/Off]
Status of trunk warning judged from trunk switch signal received from BCM with
CAN communication line.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст