Infiniti G37 Coupe. Manual — part 1350
REAR OIL SEAL
TM-253
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000001672271
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage and A/T fluid level after completing installation. Refer to
TM-254
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
REVOLUTION SENSOR
Exploded View
INFOID:0000000001672275
Removal and Installation
INFOID:0000000001672276
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust front tube and center muffler with power tool. Refer to
.
4.
Remove heat insulator.
5.
Remove rear propeller shaft. Refer to
6.
Remove control rod. Refer to
.
7.
Remove exhaust mounting bracket. Refer to
1.
Rear extension
2.
A/T
3.
Bracket
4.
Oil pan gasket
5.
Clip
6.
Oil pan mounting bolt
7.
Oil pan
8.
Drain plug
9.
Drain plug gasket
10.
Revolution sensor
11.
Self-sealing bolt
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
SCIA8271E
REVOLUTION SENSOR
TM-255
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8.
Disconnect heated oxygen sensor 2 harness connectors (A).
9.
Remove heated oxygen sensor 2 harness (B) from clips (1).
10. Remove bracket (2) from transmission assembly.
11. Remove clips (1).
12. Remove oil pan (2) and oil pan gasket.
13. Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve with TCM and trans-
mission case.
14. Remove rear engine mounting member with power tool. Refer to
15. Remove engine mounting insulator (rear). Refer to
16. Remove tightening bolts for rear extension assembly and trans-
mission case.
17. Tap rear extension assembly with a soft hammer (A).
: Vehicle front
: Bolt
SCIA8269E
3
: Drain plug
: Vehicle front
: Oil pan mounting bolt
1
: Self-sealing bolt
A
: Bolt
SCIA8117E
JPDIA0026ZZ
JPDIA0027ZZ
TM-256
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
18. Remove rear extension assembly (with needle bearing) from
transmission case.
19. Disconnect revolution sensor connector (A).
CAUTION:
Be careful not to damage connector
20. Disengage terminal clip (
).
21. Remove revolution sensor (1) from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
INSTALLATION
1.
Install revolution sensor (1) in transmission case. Tighten a nec-
essary bolt for revolution sensor with specified torque.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
SCIA3431E
JPDIA0011ZZ
: Bolt
JPDIA0041ZZ
: Bolt
JPDIA0041ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст