Infiniti G37 Coupe. Manual — part 1363

TRANSMISSION ASSEMBLY

TM-305

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

70. Install A/T fluid temperature sensor 2 (1) [with bracket (2)] in

control valve with TCM. Tighten A/T fluid temperature sensor 2
bolt to the specified torque.

CAUTION:

Adjust bolt hole of bracket to bolt hole of control valve.

71. Install control valve with TCM in transmission case.

CAUTION:

• Make sure that turbine revolution sensor securely installs

turbine revolution sensor hole (B).

• Hang down revolution sensor harness toward outside so

as not to disturb installation of control valve with TCM.

• Adjust A/T assembly harness connector of control valve

with TCM to terminal hole of transmission case.

• Assemble it so that manual valve cutout is engaged with

manual plate projection.

72. Install bolts A, B and C to control valve with TCM.

JPDIA0013ZZ

A

: Brake band

JPDIA0020ZZ

SCIA5035E

: Front

Bolt symbol

Length

mm (in)

Number of bolts

A

42 (1.65)

5

B

55 (2.17)

6

C

40 (1.57)

1

SCIA8077E

TM-306

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

73. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After

tightening them in order (1

→

2

→

3), tighten other bolts. Tighten

control valve bolts to the TCM with specified torque.

74. Connect A/T fluid temperature sensor 2 connector (A).
75. Engage terminal cord assembly and A/T fluid temperature sen-

sor 2 harness with terminal clips (

).

76. Connect revolution sensor connector (A).

77. Engage revolution sensor harness with terminal clip (

).

78. Pull down A/T assembly harness connector.

CAUTION:

Be careful not to damage connector.

79. Install snap ring to A/T assembly harness connector.

: Front

SCIA8078E

SCIA8124E

JPDIA0011ZZ

SCIA5299E

SCIA5300E

TRANSMISSION ASSEMBLY

TM-307

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

80. Install magnets (1) in oil pan.

81. Install oil pan gasket to transmission case.

CAUTION:

• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
• Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.

82. Install oil pan (2) and clips (1) to transmission case.

CAUTION:

• Install it so that drain plug (3) comes to the position as

shown in the figure.

• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.

from oil pan mounting surface.

83. Tighten oil pan mounting bolts to the specified torque in numeri-

cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque.

CAUTION:

Do not reuse oil pan mounting bolts.

84. Install drain plug to oil pan. Tighten drain plug to the specified

torque.

CAUTION:

Do not reuse drain plug gasket.

85. Pour ATF into torque converter.

• Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is

required for a new torque converter.

• When reusing old torque converter, add the same amount

of ATF as was drained.

JPDIA0009ZZ

: Front

: Oil pan mounting bolt

SCIA8117E

: Front

JPDIA0021ZZ

SAT428DA

TM-308

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

86. Install torque converter while aligning notches of torque con-

verter with notches of oil pump.

CAUTION:

Install torque converter while rotating it.

87. Measure distance (A) to make sure that torque converter is in

proper position.

Inspection

INFOID:0000000001672299

INSPECTION AFTER REMOVAL

• Check foreign materials in oil pan to help determine causes of mal-

function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build
up. Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.

- If frictional material is detected, perform A/T fluid cooler

cleaning. Refer to

TM-216, "Cleaning"

.

SCIA5010E

B

: Scale

C

: Straightedge

Distance (A)

: Refer to

TM-330, "Torque Converter"

.

JPDIA0042ZZ

SCIA5199E