Infiniti G37 Coupe. Manual — part 653
EXL-32
< FUNCTION DIAGNOSIS >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*: Initial setting
DATA MONITOR
ILL DELAY SET
MODE 1*
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE 2
Without the func-
tion
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
CUSTOM A/LIGHT SET-
TING
MODE 1*
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
Service item
Setting item
Setting
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from unified meter and A/C amp. with CAN
communication
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW-DR
[On/Off]
The switch status input from driver side door switch
DOOR SW-AS
[On/Off]
The switch status input from passenger side door switch
DIAGNOSIS SYSTEM (BCM)
EXL-33
< FUNCTION DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000001604615
WORK SUPPORT
*: Initial setting
DATA MONITOR
DOOR SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW- RL
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]
The value of exterior brightness voltage input from the optical sensor
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off
Stops the tail lamp request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Low
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
FR FOG LAMP
On
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog lights request signal transmission.
RR FOG LAMP
On
NOTE:
The item is indicated, but cannot be tested.
Off
DAYTIME RUNNING LIGHT
On
NOTE:
The item is indicated, but cannot be tested.
Off
CORNERING LAMP
RH
NOTE:
The item is indicated, but cannot be tested.
LH
Off
ILL DIM SIGNAL
On
NOTE:
The item is indicated, but cannot be tested.
Off
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only*
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob.
Unlk Only
With unlocking only
Lock/Unlk
With locking/unlocking
Off
Without the function
EXL-34
< FUNCTION DIAGNOSIS >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
Panic alarm signal status received from the remote keyless entry receiver
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps.
LH
Outputs the voltage to blink the left side turn signal lamps.
Off
Stops the voltage to turn the turn signal lamps OFF.
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-35
< FUNCTION DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000001830780
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Side maker lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan (cooling fan control module)
Operation Procedure
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5.
The oil pressure warning lamp starts blinking when the auto active test starts.
6.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system. Refer to
.
• Do not start the engine.
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
JPMIA0521ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст