Infiniti G37 Coupe. Manual — part 34
ADP-130
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000001693776
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
DRIVER SIDE : Component Function Check
INFOID:0000000001693777
1.
CHECK FUNCTION
1.
Select “MIRROR MOTOR LH” in “Active Test” mode with CONSULT-III.
2.
Check the telescopic motor operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-130, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000001693778
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
Test item
Description
MIRROR MOTOR LH
OFF
Driver side door mirror
Stop
UP
Upward
DOWN
Downward
LEFT
Leftward
RIGHT
Rightward
Terminals
Door mirror remote control switch
condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
D3
5
Ground
UP
Battery voltage
Other than above
0
6
LEFT
Battery voltage
Other than above
0
7
DOWN / RIGHT
Battery voltage
Other than above
0
Automatic drive positioner con-
trol unit connector
Terminal
Door mirror (driver side) connec-
tor
Terminal
Continuity
DOOR MIRROR MOTOR
ADP-131
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-237, "Removal and Installation"
.
4.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
ADP-131, "DRIVER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-38, "Intermittent Incident"
.
NO
>> Replace door mirror. Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Removal and Installation"
.
DRIVER SIDE : Component Inspection
INFOID:0000000001693779
1.
CHECK DOOR MIRROR MOTOR-1
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Disassembly and Assembly"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace door mirror. Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Removal and Installation"
.
2.
CHECK DOOR MIRROR MOTOR-2
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Apply 12 V to each power supply terminal of door mirror motor.
M51
16
D3
7
Existed
31
5
32
6
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
16
Not existed
31
32
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
16
Ground
DOWN / RIGHT
Battery voltage
Other than above
0
31
UP
Battery voltage
Other than above
0
32
LEFT
Battery voltage
Other than above
0
ADP-132
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror. Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000001848652
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
PASSENGER SIDE : Component Function Check
INFOID:0000000001848653
1.
CHECK FUNCTION
1.
Select “MIRROR MOTOR RH” in “Active Test” mode with CONSULT-III.
2.
Check the door mirror motor operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-132, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000001848654
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
Door mirror connector
Terminal
Operational direction
(+)
(–)
D3
7
6
RIGHT
6
7
LEFT
5
7
UP
7
5
DOWN
Test item
Description
MIRROR MOTOR RH
OFF
Passenger side door mirror
Stop
UP
Upward
DOWN
Downward
LEFT
Leftward
RIGHT
Rightward
Terminals
Door mirror remote control switch
condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
D33
5
Ground
UP
Battery voltage
Other than above
0
6
LEFT
Battery voltage
Other than above
0
7
DOWN / RIGHT
Battery voltage
Other than above
0
DOOR MIRROR MOTOR
ADP-133
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
4.
Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-237, "Removal and Installation"
.
4.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
ADP-133, "PASSENGER SIDE : Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-38, "Intermittent Incident"
.
NO
>> Replace door mirror. Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Removal and Installation"
.
PASSENGER SIDE : Component Inspection
INFOID:0000000001848655
1.
CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to
MIR-49, "DOOR MIRROR ASSEMBLY : Exploded View"
.
Automatic drive positioner control
unit connector
Terminal
Door mirror (passenger side)
connector
Terminal
Continuity
M51
14
D33
5
Existed
15
6
30
7
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
14
Not existed
15
30
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
14
Ground
UP
Battery voltage
Other than above
0
15
LEFT
Battery voltage
Other than above
0
30
DOWN / RIGHT
Battery voltage
Other than above
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст