Infiniti G37 Coupe. Manual — part 324
CCS
PRECAUTIONS
CCS-109
< PRECAUTION >
[INTELLIGENT CRUISE CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001912140
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
ICC System Service
INFOID:0000000001606971
• Do not look straight into the laser beam discharger when adjusting laser beam aiming.
• Turn the MAIN switch OFF in conditions similar to driving, such as free rollers or a chassis dynamometer.
• Do not use the ICC sensor integrated unit removing from vehicle. Never disassemble and remodel.
• Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjusting laser
beam aiming if necessary.
CCS-110
< PREPARATION >
[INTELLIGENT CRUISE CONTROL]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000001606972
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV99110100
(J-45718)
ICC target board
Uses for laser beam aiming adjustment
PKIA0358J
CCS
ICC SENSOR INTEGRATED UNIT
CCS-111
< ON-VEHICLE REPAIR >
[INTELLIGENT CRUISE CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ON-VEHICLE REPAIR
ICC SENSOR INTEGRATED UNIT
Exploded View
INFOID:0000000001606973
LEATHER GRADE TYPE
SRORT GRADE TYPE
Removal and Installation
INFOID:0000000001606974
REMOVAL
1.
Remove the front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Disconnect ICC sensor integrated unit connector.
1.
ICC sensor integrated unit
Refer to
JSOIA0002ZZ
1.
ICC sensor integrated unit
Refer to
JSOIA0003ZZ
CCS-112
< ON-VEHICLE REPAIR >
[INTELLIGENT CRUISE CONTROL]
ICC SENSOR INTEGRATED UNIT
3.
Remove mounting bolts from ICC sensor integrated unit.
4.
Remove ICC sensor integrated unit.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000001606975
ADJUSTMENT
Always perform the laser beam aiming adjustment after replacing or removing/installing the ICC sensor inte-
grated unit. Refer to
CCS-7, "LASER BEAM AIMING ADJUSTMENT : Special Repair Requirement (Prepara-
.
INSPECTION
Always perform the laser beam aiming adjustment and the ICC system operation inspection after replacing or
removing/installing the ICC sensor integrated unit. Refer to
CCS-11, "ACTION TEST : Special Repair Require-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст