Infiniti G37 Coupe. Manual — part 737
GW-16
< ON-VEHICLE REPAIR >
FRONT DOOR GLASS
FRONT DOOR GLASS
Exploded View
INFOID:0000000001741451
Removal and Installation
INFOID:0000000001744041
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "Removal and Installation"
.
2.
Disconnect front door speaker harness connector.
3.
Operate the power window main switch to raise or lower the
door window until the glass mounting bolts can be seen.
4.
Remove the glass mounting bolts.
1. Door glass assembly
2.
Corner piece assembly
3.
Module base
4.
Regulator assembly
5.
Power window motor
JMKIA1198ZZ
JMKIA1199ZZ
FRONT DOOR GLASS
GW-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5.
Hold securely the door glass and pull it out of the sash to
remove the door glass.
NOTE:
Do not raise the glass at the top upper of the door after the door
glass has been removed.
6.
Remove the door mirror assembly. Refer to
MIR-50, "DOOR MIRROR ASSEMBLY : Removal and Instal-
.
7.
Remove the door inside seal. Refer to
INT-11, "Removal and Installation"
.
8.
Remove the door glass run.
9.
Remove the front lower sash nuts, and then remove the front lower sash.
10. Remove the corner piece bolts, and then remove the corner piece.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000001741453
SYSTEM INITIALIZATION
Initialize the system if any of the following work has been done.
• Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery
cable, etc.
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Operation of the regulator assembly as a unit.
• Removal and installation of the door glass.
• Removal and installation of the body side weatherstrip and door weatherstrip.
• Disconnection and connection of the minus terminal of battery.
Initialization
Follow the steps below after installing each component to the vehicle.
1.
Disconnect the minus terminal of battery or disconnect power window switch harness connector tempo-
rarily. Then reconnect after at least 1 minute.
2.
Close the door.
3.
Turn ignition switch ON.
4.
Operate power window switch to make over a half of the window open area.
5.
Press the power window switch in the up direction (auto close position) and hold. Continue holding the
switch even when window is completely closed and then release after 3 seconds.
6.
Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1.
Open fully the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3.
Perform fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.91
in) or for 2 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
JMKIA1200ZZ
GW-18
< ON-VEHICLE REPAIR >
FRONT DOOR GLASS
• Be careful not to be pinched.
• Check that the auto up function is normal before the inspection following the system initialization.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
body side weatherstrip is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass
and guide rail mounting bolts to correct the glass position if the clearance between the glass and body side
weatherstrip is not parallel.
• Raise the glass fully and adjust the glass top end and body side welt fitting with the adjusting bolt (1), (2), or
(3) as shown in the figure below.
NOTE:
• Always start at adjusting bolt (1). If the desired angle is not achieved, then proceed to adjusting bolt (2) and
(3) respectively.
• Turn the adjusting bolt clockwise (b) to move the door glass upper end outward.
• Turn the adjusting bolt anticlockwise (a) to move the door glass upper end inward.
• Adjustment process with adjusting bolt (3) is the inverse of adjusting bolt (1) and (2).
• When adjusting with adjusting bolt (3), turn the adjusting bolt clockwise to move the door glass upper end
inward, then anticlockwise to move the door glass upper end outward.
JMKIA1386ZZ
FRONT REGULATOR
GW-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT REGULATOR
Exploded View
INFOID:0000000001744606
Removal and Installation
INFOID:0000000001744607
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "Removal and Installation"
2.
Disconnect front door speaker harness connector.
3.
Operate the power window main switch to raise or lower the
door window until the glass mounting bolts can be seen.
4.
Remove the glass mounting bolts.
1. Door glass assembly
2.
Corner piece assembly
3.
Module base
4.
Regulator assembly
5.
Power window motor
JMKIA1198ZZ
JMKIA1199ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст