Infiniti G37 Coupe. Manual — part 1065
RSU-10
< ON-VEHICLE REPAIR >
REAR LOWER LINK & COIL SPRING
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
REAR SHOCK ABSORBER
RSU-11
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000001686607
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
JPEIB0059ZZ
RSU-12
< ON-VEHICLE REPAIR >
REAR SHOCK ABSORBER
Removal and Installation
INFOID:0000000001671754
REMOVAL
1.
Remove tires with power tool.
2.
Set suitable jack under axle assembly to relieve the coil spring tension.
3.
Remove shock absorber lower end bolt with power tool.
4.
Gradually lower the jack to remove it from rear lower link.
5.
Remove shock absorber assembly upper end nuts with power
tool, and then remove shock absorber assembly from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the shock absorber lower side (rubber bushing), under unladen
conditions with tires on level ground.
Disassembly and Assembly
INFOID:0000000001671755
DISASSEMBLY
CAUTION:
Never damage shock absorber piston rod when removing components from shock absorber.
1.
Remove cap from mounting bracket
2.
Wrap a shop cloth around lower side of shock absorber and fix it with a vise.
CAUTION:
Never set the cylindrical part of shock absorber with a vise.
3.
Secure the piston rod tip so that piston rod does not turn, and remove piston rod lock nut.
4.
Remove mounting seal, mounting bracket and bound bumper cover from shock absorber.
ASSEMBLY
Install in the reverse order of removal.
Inspection
INFOID:0000000001671756
INSPECTION AFTER REMOVAL
• Check shock absorber assembly for deformation, cracks, damage, and replace if there are.
• Check welded and sealed areas for oil leakage, and replace if there are.
INSPECTION AFTER INSTALLION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
JPEIB0060ZZ
REAR SHOCK ABSORBER
RSU-13
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
INSPECTION AFTER DISASSEMBLY
Bound Bumper and Bushing
Check bound bumper cover and bushing for cracks and damage. Replace if there are.
Shock Absorber
Check the following:
• Shock absorber for deformation, cracks, and other damage. Replace if there are.
• Piston rod for damage, uneven wear, and distortion. Replace if there are.
INSPECTION AFTER ASSEMBLY
Make sure piston rod on shock absorber is not damaged when attaching components to shock absorber.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст