Infiniti G37 Coupe. Manual — part 540
P0507 ISC SYSTEM
EC-341
< COMPONENT DIAGNOSIS >
[VQ37VHR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0507 ISC SYSTEM
Description
INFOID:0000000001910897
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan
operation, etc.).
DTC Logic
INFOID:0000000001734161
DTC DETECTION LOGIC
NOTE:
If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
If the target idle speed is out of the specified value, perform
EC-19, "IDLE AIR VOLUME LEARNING :
, before conducting DTC Confirmation Procedure.
TESTING CONDITION:
• Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
• Always perform the test at a temperature above
−
10
°
C(14
°
F).
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Start engine and run it for at least 1 minute at idle speed.
6.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001734162
1.
CHECK PCV HOSE CONNECTION
Confirm that PCV hose is connected correctly.
Is the inspection result normal?
YES
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0507
Idle speed control sys-
tem RPM higher than
expected
The idle speed is more than the target idle
speed by 200 rpm or more.
• Electric throttle control actuator
• Intake air leak
• PCV system
EC-342
< COMPONENT DIAGNOSIS >
[VQ37VHR]
P0507 ISC SYSTEM
NO
>> Repair or replace.
2.
CHECK INTAKE AIR LEAK
1.
Start engine and let it idle.
2.
Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES
>> Discover air leak location and repair.
NO
>> GO TO 3.
3.
REPLACE ECM
1.
Stop engine.
2.
Replace ECM.
3.
EC-16, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (ECM) : Special Repair
.
>> INSPECTION END
P0524 ENGINE OIL PRESSURE
EC-343
< COMPONENT DIAGNOSIS >
[VQ37VHR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0524 ENGINE OIL PRESSURE
DTC Logic
INFOID:0000000001903474
DTC DETECTION LOGIC
NOTE:
If DTC P0524 is displayed with DTC P0075 or P0081, first perform the trouble diagnosis for DTC P0075,
P0081. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING-I
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10V and 16V at
idle.
>> GO TO 2.
2.
PRECONDITIONING-II
Check oil level and oil pressure. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Go to
.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1.
Select “DATA MONITOR” mode with CONSULT-III.
2.
Maintain the following conditions for at least 20 consecutive seconds.
CAUTION:
Always drive at a safe speed.
3.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT-III” above.
DTC No.
Trouble diagnosis
name
Detecting condition
Possible cause
P0524
Engine oil pressure
too low
Engine oil pressure is low because there is a
gap between angle of target and phase-control
angle.
• Engine oil pressure or level too low
• Crankshaft position sensor (POS)
• Camshaft position sensor (PHASE)
• Intake valve control solenoid valve
• Accumulation of debris to the signal pick-up
portion of the camshaft
• Timing chain installation
• Foreign matter caught in the oil groove for in-
take valve timing control
ENG SPEED
More than 1,700 rpm
COOLAN TEMP/S
More than 70
°
C (158
°
F)
Selector lever
1st or 2nd position
Driving location uphill
Driving vehicle uphill
(Increased engine load will help maintain the driving
conditions required for this test.)
EC-344
< COMPONENT DIAGNOSIS >
[VQ37VHR]
P0524 ENGINE OIL PRESSURE
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001910863
1.
CHECK OIL PRESSURE WARNING LAMP
1.
Start engine.
2.
Check oil pressure warning lamp and confirm it is not illumi-
nated.
Is oil pressure warning lamp illuminated?
YES
>> Go to
.
NO
>> GO TO 2.
2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
EC-153, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning intake valve timing control solenoid valve.
3.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-267, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace crankshaft position sensor (POS).
4.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
EC-271, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning camshaft position sensor (PHASE).
5.
CHECK CAMSHAFT (INTAKE)
Check the following.
• Accumulation of debris to the signal plate of camshaft front end
• Chipping signal plate of camshaft front end
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Remove debris and clean the signal plate of camshaft
front end or replace camshaft.
6.
CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned?
YES
>> Check timing chain installation. Refer to
EM-49, "Removal and Installation"
.
NO
>> GO TO 7.
PBIA8559J
JMBIA0962ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст