Infiniti G37 Coupe. Manual — part 1293
TRANSMISSION ASSEMBLY
TM-25
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000001732877
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder) body and CSC tube.
Return CSC body insert to original position to remove transmission assembly. Dust on clutch disc sliding parts may damage
seal of CSC body and may cause clutch fluid leakage.
Removal and Installation
INFOID:0000000001732878
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylin-
der) body and CSC tube. Return CSC body insert to original position to remove transmission assem-
bly. Dust on clutch disc sliding parts may damage seal of CSC body and may cause clutch fluid
leakage.
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove exhaust mounting bracket. Refer to
EX-6, "Removal and Installation"
3.
Remove suspension member stay. Refer to
FSU-24, "Removal and Installation"
4.
Remove exhaust front tube, center muffler, and main muffler. Refer to
EX-6, "Removal and Installation"
5.
Remove propeller shaft assembly. Refer to
DLN-7, "Removal and Installation"
.
NOTE:
Insert a suitable plug into rear oil seal of transmission assembly after removing propeller shaft assembly.
6.
Remove control lever assembly with the following procedure.
1.
Harness bracket
2.
Transmission assembly
: For the bolt mounting positions, refer to
TM-25, "Removal and Installation"
.
Refer to
for symbols not described on the above.
JPDIC0158GB
TM-26
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
a.
Remove control rod mounting bolt and then separate control
lever assembly from control rod.
b.
Remove console finisher assembly as shown in the figure. Refer
to
IP-24, "Removal and Installation"
c.
Remove felt as shown in the figure.
d.
Remove center console assembly to remove hole cover as
shown in the figure. Refer to
IP-24, "Removal and Installation"
e.
Remove hole cover.
f.
Remove control lever boot B, hole insulator, and control lever
boot A.
SCIA1364E
JPDIC0018ZZ
JPDIC0019ZZ
JPDIC0020ZZ
JPDIC0021ZZ
TRANSMISSION ASSEMBLY
TM-27
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
g.
Remove guide plate mounting bolts and then remove control
lever assembly and control lever spring from control lever hous-
ing.
CAUTION:
Restrain guide plate while doing this because there is a
danger control lever assembly will fly out of control lever
housing.
7.
Remove clutch tube (1), clutch hose (2), and lock plate (3).
Refer to
CL-14, "Removal and Installation"
.
CAUTION:
• Keep painted surface on the body or other parts free of
clutch fluid. If it spills, wipe up immediately and wash the
affected area with water.
• Never depress clutch pedal during removal procedure.
NOTE:
Insert a suitable plug into clutch hose and CSC (Concentric
Slave Cylinder) tube after removing clutch tube.
8.
Remove crankshaft position sensor. Refer to
EM-111, "Disassembly and Assembly"
CAUTION:
• Handle carefully to avoid dropping and shocks.
• Never disassemble.
• Never allow metal powder to adhere to magnetic part at sensor tip.
• Never place sensors in a location where they are exposed to magnetism.
9.
Remove starter motor. Refer to
STR-16, "Removal and Installation"
.
10. Remove rear plate cover. Refer to
.
11. Disconnect park/neutral position (PNP) switch harness connec-
tor.
12. Disconnect heated oxygen sensor 2 (bank 1) and heated oxy-
gen sensor 2 (bank 2) harness connectors. Refer to
13. Remove harness brackets.
14. Set a suitable jack to the transmission assembly.
CAUTION:
When setting a suitable jack, be careful so that it does not
contact with the switch.
15. Remove engine mounting insulator (rear) mounting nuts. Refer
EM-67, "Removal and Installation"
.
16. Remove rear engine mounting member. Refer to
17. Remove engine and transmission mounting bolts with power
tool.
18. Lower a suitable jack to the position where the back-up lamp
switch harness connector can be disconnect. Then disconnect back-up lamp switch harness connector.
19. Remove transmission assembly from the vehicle.
CAUTION:
JPDIC0022ZZ
: Vehicle front
JPDIC0026ZZ
JPDIC0024ZZ
JPDIC0023ZZ
TM-28
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
• Secure transmission assembly to a suitable jack while removing it.
• The transmission assembly must not interfere with the three way catalyst (right bank) and three
way catalyst (left bank).
• The transmission assembly must not interfere with the wire harnesses and clutch hose.
• Never hold control lever housing to prevent bushing of control lever housing from deformation
when moving transmission assembly.
20. Remove CSC (Concentric Slave Cylinder) body and CSC tube. Refer to
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cyl-
inder) body and CSC tube. Return CSC body insert to original position to remove transmission
assembly. Dust on clutch disc sliding parts may damage seal of CSC body and may cause clutch
fluid leakage.
21. Remove dynamic damper. Refer to
EM-67, "Removal and Installation"
INSTALLATION
Note the following, and install in the reverse order of removal.
• Tighten transmission assembly mounting bolts to the specified
torque. The figure is the view from the vehicle forward.
CAUTION:
• The transmission assembly must not interfere with the three way catalyst (right bank) and three
way catalyst (left bank).
• The transmission assembly must not interfere with the wire harnesses and clutch hose.
• When installing transmission assembly, never bring main drive gear into contact with clutch cover.
• Never hold control lever housing to prevent bushing of control lever housing from deformation
when moving transmission assembly.
• Refer to
CL-15, "Removal and Installation"
for CSC (Concentric Slave Cylinder) body and CSC tube installa-
tion procedure.
• Refer to
CL-14, "Removal and Installation"
for clutch tube and clutch hose installation procedure.
• Refer to
TM-18, "Removal and Installation"
for control lever assembly installation procedure.
• After installation, check for oil leakage and oil level. Refer to
.
• If flywheel is removed, align dowel pin with the smallest hole of flywheel. Refer to
: Transmission to engine
: Engine to transmission
: With air breather tube
Bolt symbol
A
B
Quantity
8
4
Bolt length
“
” mm (in)
65 (2.56)
35 (1.38)
Tightening torque
N·m (kg-m, ft-lb)
75 (7.7, 55)
46.6 (4.8, 34)
JPDIC0341ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст