Infiniti G37 Coupe. Manual — part 1453
WW-86
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Hydraulic Layout
INFOID:0000000001629642
Removal and Installation
INFOID:0000000001629643
REMOVAL
1.
Open the hood.
2.
Use the stop point of washer nozzle (1) as the support point and
rotate nozzle to remove it from body, while pushing nozzle spray
point side along the hood.
3.
Remove the washer tube (2) from the washer nozzle.
INSTALLATION
1.
Install washer tube into the washer nozzle.
2.
Install the washer nozzle to the hood.
3.
Adjust the washer nozzle spray position. Refer to
WW-86, "Inspection and Adjustment"
CAUTION:
The spray positions differ. Check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000001629644
INSPECTION
Washer Nozzle Inspection
1.
Washer tube
2.
Washer nozzle
3.
Washer tube
4.
Washer tank
: Clip
: Clip
JPLIA0560ZZ
JPLIA0561ZZ
FRONT WASHER NOZZLE AND TUBE
WW-87
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA0562ZZ
1
: Black printed frame line
: Vehicle front
Spray
position
H : Height
L : Width
φ
: Spray point area
A
161 (6.34)
458 (18.03)
80 (3.15)
B
276 (10.87)
308 (12.13)
80
×
155 (3.15
×
6.10)
C
270 (10.63)
113 (4.45)
80
×
170 (3.15
×
6.69)
D
284 (11.18)
92 (3.62)
80
×
180 (3.15
×
7.09)
E
306 (12.05)
306 (12.05)
80
×
160 (3.15
×
6.30)
F
279 (10.98)
439 (17.28)
80
×
130 (3.15
×
5.12)
JPLIA0563ZZ
JPLIA0564ZZ
WW-88
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000001629645
Removal and Installation
INFOID:0000000001629646
REMOVAL
1.
Operate the front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Remove wiper arm cap.
4.
Remove the wiper arm mounting nut.
5.
Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2.
Operate the front wiper motor to move the wiper to the auto stop position.
3.
Adjust the wiper blade position. Refer to
.
4.
Install the wiper arm by tightening the mounting nut.
5.
Inject the washer fluid.
6.
Operate the front wiper to move it to the auto stop position.
7.
Check that the wiper blades stop at the specified position.
8.
Install wiper arm cap.
1.
Wiper blade (RH)
2.
Wiper arm (RH)
3.
Wiper arm cap
4.
Wiper arm (LH)
5.
Wiper blade (LH)
Refer to
for symbols in the figure.
JPLIA0085GB
ELH0717D
FRONT WIPER ARM
WW-89
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Adjustment
INFOID:0000000001629647
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover and the top of wiper blade center
Standard clearance
R
: 37
±
7.5 mm (1.457
±
0.295 in)
L
: 60
±
7.5 mm (2.362
±
0.295 in)
JPLIA0082ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст