Infiniti G37 Coupe. Manual — part 430
DLN-34
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
SIDE OIL SEAL
Removal and Installation
INFOID:0000000001714218
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove rear wheel sensor. Refer to
3.
Remove drive shaft from final drive with a power tool. Then suspend it by wire, etc. Refer to
4.
Install attachment (A) [SST: KV40104100 (
—
)] to side
flange, and then pull out the side flange with the sliding hammer
(B) [SST: ST36230000 (J-25840-A)].
NOTE:
Circular clip installation position: Final drive side
5.
Remove side oil seal, using a flat-bladed screwdriver.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to side oil seal lips.
2.
Install side oil seal until it becomes flush with the case end,
using the drift [SST: KV38100200 (J-26233)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
3.
Install side flange with the following procedure.
a.
Attach the protector [SST: KV38107900 (J-39352)] to side oil
seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until sound changes.
JSDIA0105ZZ
SDIA1584E
SDIA1585E
SDIA0822E
SIDE OIL SEAL
DLN-35
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NOTE:
When installation is completed, driving sound of the side flange turns into a sound that seems to affect the
whole final drive.
d.
Confirm that the dimension of the side flange (1) installation
(Measurement A) in the figure comes into the following.
4.
Install drive shaft. Refer to
5.
Install rear wheel sensor. Refer to
6.
Install center muffler. Refer to
.
7.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
Measurement “A”
: 326 – 328 mm (12.83 –
12.91 in)
JSDIA0106ZZ
DLN-36
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
REAR FINAL DRIVE ASSEMBLY
REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000001714221
Removal and Installation
INFOID:0000000001714222
REMOVAL
1.
Remove center muffler with a power tool. Refer to
2.
Remove rear stabilizer bar with a power tool. Refer to
.
3.
Remove propeller shaft from the final drive. Refer to
.
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire, etc. Refer to
.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
.
1.
Rear final drive assembly
2.
Upper stopper
3.
Lower stopper
4.
Washer
: Vehicle front
Refer to
for symbols in the figure.
JPDID0127GB
SDIA1094E
REAR FINAL DRIVE ASSEMBLY
DLN-37
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Never place a jack on the rear cover (aluminum case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member, and remove rear final drive assembly with a power
tool.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
• When installing breather hoses (1), refer to the figure.
CAUTION:
Make sure there are no pinched or restricted areas on the
breather hose caused by bending or winding when installing
it.
- For installation, insert the vehicle side end to suspension member
(2). Install metal connector (3) side of this hose to rear cover by
inserting it with aiming painted marking to the front of vehicle.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
.
JSDIA0026ZZ
: Vehicle front
PDIA0754E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст