Infiniti G37 Coupe. Manual — part 1226
ST-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
Reference
—
,
,
NVH in DLN section.
NVH in DLN section.
NVH i
n
F
AX,
RAX,
FSU, RSU section.
NVH in WT section.
NVH in WT section.
NVH in F
AX section.
NVH in B
R
section.
Possible cause and SUSPECTED PARTS
Fl
uid
l
e
vel
Ai
r in
hy
dra
u
lic
sy
s
tem
Out
e
r/i
n
n
e
r s
o
c
k
e
t
bal
l j
o
in
t s
w
in
gi
ng
to
rque
Ou
te
r/in
ne
r so
cke
t
b
a
ll
jo
in
t ro
ta
tin
g
t
o
rq
ue
Ou
te
r/
in
ne
r so
cke
t
b
a
ll jo
in
t en
d pl
a
y
S
tee
ring
fl
ui
d l
e
a
k
a
g
e
S
tee
ring
wh
ee
l p
lay
S
te
e
ri
n
g
ge
ar ra
ck
s
lid
in
g f
o
rc
e
Dri
ve
b
e
lt
lo
os
en
es
s
Im
p
rop
er st
e
e
ri
ng
whe
e
l
Im
pro
pe
r in
st
al
lat
ion
o
r lo
os
en
es
s
of t
ilt
lo
ck
le
ve
r
M
ou
nti
ng
lo
os
en
es
s
S
tee
ring
c
o
lu
m
n
d
e
fo
rm
ati
o
n
or
da
ma
ge
Im
pro
p
e
r in
st
al
lat
ion
o
r lo
os
en
es
s
of s
te
e
ri
ng
co
lu
mn
S
tee
ring
l
ink
ag
e
loo
s
e
ne
s
s
4W
AS f
ron
t a
ct
u
a
tor
PROPELLER S
H
AFT
DIFF
ERENTIAL
AXLE and SUSPENSI
ON
TI
RE
S
ROAD WHEE
L
DRIVE SHAFT
BRAKE
S
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
ST-5
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
×
: Applicable
Symptom
Steering
Noise
× × × × × × × × ×
× ×
× × × × × × ×
Shake
×
×
×
× × × × ×
Vibration
×
× × ×
×
× ×
×
Shimmy
×
×
× ×
× × ×
×
Judder
×
× ×
× × ×
×
ST-6
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001751539
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000001751540
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
Service Notice or Precautions for Steering System
INFOID:0000000001666216
CAUTION:
• In case of removing steering gear assembly, make the final tightening with grounded and unloaded
vehicle condition, and then check wheel alignment.
• Observe the following precautions when disassembling.
PRECAUTIONS
ST-7
< PRECAUTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from
becoming contaminated by dirt or other foreign matter.
- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might inter-
fere with their operation.
- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст