Infiniti G37 Coupe. Manual — part 423
DLN-6
< ON-VEHICLE MAINTENANCE >
[REAR PROPELLER SHAFT: 3S80A]
REAR PROPELLER SHAFT
ON-VEHICLE MAINTENANCE
REAR PROPELLER SHAFT
Inspection
INFOID:0000000001714145
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1.
Measure propeller shaft runout at several points by rotating final
drive companion flange with hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 90,
180, 270 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
Propeller shaft runout measuring point (Point “ ”).
Limit
Propeller shaft runout
SDIA1087E
: Vehicle front
Dimension
A: 192 mm (7.56 in)
B: 172 mm (6.77 in)
C: 170 mm (6.69 in)
PDIA0770J
REAR PROPELLER SHAFT
DLN-7
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3S80A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ON-VEHICLE REPAIR
REAR PROPELLER SHAFT
Exploded View
INFOID:0000000001714146
Removal and Installation
INFOID:0000000001714147
REMOVAL
1.
Move the M/T shift lever to neutral position and release the parking brake.
2.
Remove the floor reinforcement.
3.
Remove the center muffler with power tool. Refer to
4.
Remove the heat plate (1).
1.
Clip
2.
Center bearing mounting bracket
(Upper)
3.
Propeller shaft assembly
4.
Center bearing mounting bracket
(Lower)
: Vehicle front
Refer to
JSDIA0124GB
JSDIA0006ZZ
DLN-8
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3S80A]
REAR PROPELLER SHAFT
5.
Put matching marks on propeller shaft flange yoke with final
drive companion flange.
CAUTION:
For matching marks, use paint. Never damage propeller
shaft flange yoke and final drive companion flange.
6.
Loosen mounting nuts of center bearing mounting brackets.
CAUTION:
Tighten mounting nuts temporarily.
7.
Remove propeller shaft assembly fixing bolts and nuts.
8.
Remove center bearing mounting bracket fixing nuts.
9.
Remove propeller shaft assembly.
CAUTION:
• Never damage the rear oil seal of transmission.
• If constant velocity joint was bent during propeller shaft
assembly removal, installation, or transportation, its boot
may be damaged. Wrap boot interference area to metal
part with shop cloth or rubber to protect boot from break-
age.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install center bearing mounting bracket (Upper) (1) with its arrow
mark (A) facing forward.
• Adjust position of center bearing mounting bracket (1, 2) sliding
back and forth to prevent play in thrust direction of center bearing
insulator (3). Install bracket to vehicle.
SDIA1822E
PDIA0402E
JSDIA0127ZZ
REAR PROPELLER SHAFT
DLN-9
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3S80A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Align matching marks to install propeller shaft flange yoke with final
drive companion flange.
• After assembly, perform a driving test to check propeller shaft
vibration. If vibration occurred, separate propeller shaft from final
drive. Reinstall companion flange after rotating it by 90, 180, 270
degrees. Then perform driving test and check propeller shaft vibra-
tion again at each point.
• If propeller shaft or final drive has been replaced, connect them as
follows:
- Install the propeller shaft while aligning its matching mark (A) with
the matching mark (B) on the joint as close as possible.
CAUTION:
Never damage the rear oil seal of transmission.
Inspection
INFOID:0000000001714148
APPEARANCE
• Check propeller shaft for bend and damage. If damage is detected, replace propeller shaft assembly.
PROPELLER SHAFT RUNOUT
• Check propeller shaft runout at measuring points. If runout
exceeds specifications, replace propeller shaft assembly. For mea-
suring point, refer to
JOURNAL AXIAL PLAY
• As shown in the figure, while fixing yoke on one side, check axial
play of joint. If outside the standard, replace propeller shaft assem-
bly.
CAUTION:
Never disassemble joints.
CENTER BEARING
• Check center bearing for noise and damage. If noise or damage is detected, replace propeller shaft assem-
bly.
CAUTION:
Never disassemble center bearing.
SDIA1822E
PDIA0423E
Limit
Propeller shaft runout
: Refer to
.
JSDIA0111ZZ
Standard
Journal axial play
: Refer to
PDA0005D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст