Infiniti G37 Coupe. Manual — part 1299
TRANSMISSION ASSEMBLY
TM-49
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25. Apply recommended grease to check ball and then install check
ball and check ball spring into adapter plate.
26. Apply recommended sealant to threads of check ball plugs and
then tighten check ball plug to the specified torque.
• Use Genuine Silicone RTV or an equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Remove old sealant and oil adhering to threads.
27. Install 3rd-4th control lever to adapter plate and then tighten
mounting bolts to the specified torque.
CAUTION:
• Make sure the top and bottom are oriented correctly.
• Never drop shifter cap.
28. Apply recommended grease to check ball and then install check
balls and check ball springs into adapter plate.
29. Apply recommended sealant to threads of check ball plugs and
then tighten check ball plugs to the specified torque.
• Use Genuine Silicone RTV or an equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Remove old sealant and oil adhering to threads.
30. Install striking rod to adapter plate.
31. Install striking lever to striking rod.
32. Using a pin punch to tap retaining pin into striking lever.
CAUTION:
Never reuse retaining pin.
33. Install baffle plate to adapter plate and then tighten mounting
bolts to the specified torque.
PCIB0144E
PCIB1352E
PCIB0143E
PCIB0414E
PCIB0154E
TM-50
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
CASE AND EXTENSION
1.
Install counter front bearing to transmission case.
2.
Install oil gutter to transmission case.
3.
Install breather tube to transmission case.
CAUTION:
Never reuse breather tube.
4.
Apply recommended sealant to transmission case adapter plate
mounting surface as shown in the figure.
• Use Genuine Silicone RTV or an equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adhering
to both mounting surfaces.
5.
Place adapter plate in transmission case using a soft hammer to
tap adapter plate to install it into transmission case.
6.
Install snap ring to main drive gear bearing using snap ring pli-
ers.
CAUTION:
Never reuse snap ring.
PCIB0436E
PCIB1373E
SCIA1436E
SCIA1532E
TRANSMISSION ASSEMBLY
TM-51
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Tighten baffle plate mounting nut to the specified torque.
8.
Apply multi-purpose grease to lip of front cover oil seal (1).
9.
Install front cover oil seal to front cover using the drift (A) [SST:
KV38102100 (J-25803-01)].
CAUTION:
• Never reuse front cover oil seal.
• When installing, never incline front cover oil seal.
10. Install front cover according to the following.
a.
Install front cover gasket and front cover to transmission case.
CAUTION:
• Never reuse front cover gasket.
• Never damage front cover oil seal.
• Remove any moisture, oil, or foreign material adhering to
both mating surfaces.
b.
Temporary tightening mounting bolt (
) and sealing bolt (1).
c.
Temporary tightening remaining mounting bolts (
) and sealing
bolts (1).
SCIA1443E
Dimension “H”
: 8.55 - 9.55 mm (0.3366 - 0.3760 in)
JPDIC0028ZZ
JPDIC0344ZZ
JPDIC0343ZZ
TM-52
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
d.
Tighten mounting bolts (
) and sealing bolts (1) to the specified
torque in order as shown on the figure.
11. Install rear extension oil gutter and cap to rear extension and
then tighten mounting bolt to specified torque.
12. Install bracket to transmission case and then tighten mounting
bolt to specified torque.
13. Apply recommended grease to reverse idler needle bearing.
14. Install reverse idler shaft, reverse idler needle bearing, reverse
idler gear and reverse idler thrust washer to adapter plate.
15. Apply multi-purpose grease to striking rod oil seal lip.
CAUTION:
Never reuse striking rod oil seal.
16. Install striking rod oil seal to rear extension using the drift [SST:
ST33061000 (J-8107-2)].
CAUTION:
When installing, never incline striking rod oil seal.
17. Apply multi-purpose grease to lip of rear oil seal (1).
CAUTION:
Never reuse rear oil seal.
18. Install rear oil seal to rear extension using the drift [SST:
ST33400001 (J-26082)].
CAUTION:
When installing, never incline rear oil seal.
19. Apply recommended sealant to adapter plate rear extension
mounting surface as shown in the figure.
• Use Genuine Silicone RTV or an equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adhering
to both mounting surfaces.
20. Install rear extension to adapter plate and then tighten mounting
bolts to the specified torque in order as shown on the figure.
CAUTION:
Never damage rear oil seal and striking rod oil seal.
21. Install control lever housing to rear extension and then tighten
mounting bolts to the specified torque.
CAUTION:
Never hold control lever housing to prevent bushing of con-
trol lever housing from deformation when moving transmis-
sion assembly.
JPDIC0345ZZ
PCIB0213E
Dimension “H”
: 1.2 - 2.2 mm (0.047 - 0.087 in)
JPDIC0033ZZ
PCIB1374E
PCIB0256E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст