Infiniti G37 Coupe. Manual — part 711
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
Use the following procedure to check for fuel leaks.
1.
Turn ignition switch “ON” (with engine stopped), then check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
FL-10
< ON-VEHICLE REPAIR >
FUEL TANK
FUEL TANK
Exploded View
INFOID:0000000001547700
Removal and Installation
INFOID:0000000001547701
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
REMOVAL
• Drain fuel from fuel tank if necessary. Refer to
• Perform work on level place.
1.
Perform steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY” on main and sub fuel level sensor units. Refer to
2.
Remove exhaust front tube, center muffler and main muffler. Refer to
.
3.
Remove propeller shaft. Refer to
(M/T models) or
models).
4.
Remove parking rear brake cables. Refer to
PB-8, "LEVER TYPE : Exploded View"
5.
Remove rear suspension assembly. Refer to
.
1.
Fuel filler cap
2.
Grommet
3.
Fuel filler tube
4.
Clamp
5.
Vent hose
6.
Vent tube
7.
Vent hose
8.
EVAP hose
9.
Clamp
10. Clamp
11.
Fuel filler hose
12. Fuel tank mounting band
13. Fuel tank protector
14.
Insulator
15. Fuel tank
Refer to
for to symbols in the figure.
JPBIA0155GB
FUEL TANK
FL-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
6.
Remove fuel tank protector.
7.
Disconnect fuel filler hose (1), vent hose (2) and EVAP hoses (3)
at fuel tank side.
8.
Support the lower part of fuel tank (1) with transmission jack (A).
CAUTION:
Support the position that fuel tank mounting bands never
engage.
9.
Remove fuel tank mounting bands.
10. Supporting with hands, descend transmission jack carefully, and remove fuel tank.
CAUTION:
• Check that all connection points have been disconnected.
• Confirm there is no interference with vehicle.
11. Remove fuel filler tube, as necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Surely clamp fuel hoses and insert hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel tube.
• Tighten the clamp hand with the top mark until the mark is on the
bolt head flange “A”.
• To connect quick connector, refer to
.
Inspection
INFOID:0000000001547702
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
4
: Fuel tank protector
: Vehicle front
JPBIA0144ZZ
JPBIA0145ZZ
Fuel filler hose
: 35 mm (1.38 in)
The other hoses
: 25 mm (0.98 in)
JPBIA0146ZZ
FL-12
< ON-VEHICLE REPAIR >
FUEL TANK
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and check there are no fuel leaks at the fuel system tube and hose connections.
• After removing/installing rear suspension assembly, check to adjust wheel alignment and then, adjust neutral
position of steering angle sensor. Refer to
RSU-6, "Wheel Alignment Inspection"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст