Infiniti G37 Coupe. Manual — part 227
BCS-26
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000001830813
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000001830807
WORK SUPPORT
*: Initial setting
DATA MONITOR
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
TP 4
Indicates the number of ID which has been registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT-III screen touched.
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ROOM LAMP BAT SAV SET
On*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
INFOID:0000000001830803
BCM CONSULT-III FUNCTION
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from front request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ACC RLY-F/B
[On/Off]
ACC relay feedback signal status input from ACC relay
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
UNLK SEN-DR
[On/Off]
Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off]
The switch status input driver side front door switch
DOOR SW-AS
[On/Off]
The switch status input from passenger side door switch
DOOR SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW- RL
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
CDL LOCK SW
[On/Off]
Lock switch status received from the door lock and unlock switch by power window
switch serial link
CDL UNLOCK SW
[On/Off]
Unlock switch status received from the door lock and unlock switch by power window
switch serial link
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch by power window switch serial
link
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch by power window switch serial
link
TRNK/HAT MNTR
[On/Off]
The switch status input from trunk room lamp switch
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply to turn interior room lamp OFF.
On
Outputs the interior room lamp power supply to turn interior room lamp ON.*
BCS-28
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)
INFOID:0000000001830814
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
Monitor Item
Contents
PUSH SW
Indicates [ON/OFF] condition of push switch.
UNLK SEN -DR
Indicates [ON/OFF] condition of unlock sensor.
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter.
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored.
TR CANCEL SW
Indicates [ON/OFF] condition of trunk lid opener cancel switch.
TR/BD OPEN SW
Indicates [ON/OFF] condition of trunk lid opener switch.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
RKE-TR/BD
Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitored Item
Description
REQ SW-DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN-DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
This is displayed even when it is not equipped.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.
KEY CYL SW-TR
This is displayed even when it is not equipped.
TR/BD OPEN SW
Indicates [ON/OFF] condition of trunk lid opener switch.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WORK SUPPORT
ACTIVE TEST
RETAIND PWR
RETAIND PWR : CONSULT-III Function (BCM - RETAINED PWR)
INFOID:0000000001830815
Data monitor
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
INFOID:0000000001612396
DATA MONITOR
ACTIVE TEST
AIR PRESSURE MONITOR
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
Monitored Item
Description
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on
CONSULT-III screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-III screen is touched.
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
HEADLAMP(HI)
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
seconds after “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activat-
ed after “ON” on CONSULT-III screen is touched.
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT]
Description
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch (push switch) judged by BCM.
Test item
Opera-
tion
Description
OIL PRESSURE SW
Off
OFF
On
BCM transmits the oil pressure switch signal to the unified meter and A/C amp. via CAN com-
munication, which illuminates the oil pressure warning lamp in the combination meter.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст