Infiniti G37 Coupe. Manual — part 1322
P0744 A/T TCC S/V FUNCTION (LOCK -UP)
TM-141
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0744 A/T TCC S/V FUNCTION (LOCK -UP)
Description
INFOID:0000000001672159
This malfunction is detected when the A/T does not shift into 5th gear position or the torque converter clutch
does not lock-up as instructed by the TCM. This is not only caused by electrical malfunction (circuits open or
shorted) but also by mechanical malfunction such as control valve sticking, improper solenoid valve operation,
etc.
DTC Logic
INFOID:0000000001672160
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR”.
3.
Drive vehicle and maintain the following conditions for at least 30 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0744 A/T TCC S/V FUNTN” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000001672161
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
OK
>> Replace the control valve with TCM. Refer to
NG
>> Repair or replace damaged parts.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0744
A/T TCC S/V FUNTN
3rd
• A/T cannot perform
lock-up even if electri-
cal circuit is good.
• TCM detects as irregu-
lar by comparing dif-
ference value with slip
rotation.
• Harness or connectors
(Sensor circuit is open
or shorted.)
• Torque converter
clutch solenoid valve
• Hydraulic control cir-
cuit
ACCELE POSI
: More than 1.0/8
SLCT LVR POSI
: “D” position
TCC SOLENOID
: 0.4 – 0.6 A
VEHICLE SPEED
: 80 km/h (50 MPH) or more
Driving location
: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions
required for this test.
TM-142
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0745 LINE PRESSURE SOLENOID VALVE
P0745 LINE PRESSURE SOLENOID VALVE
Description
INFOID:0000000001672162
The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in
response to a signal transmitted from the TCM.
DTC Logic
INFOID:0000000001672163
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine and wait for at least 5 seconds.
2.
Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0745 L/PRESS SOL/CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000001672164
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace the control valve with TCM. Refer to
NO
>> Repair or replace damaged parts.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0745
L/PRESS COL/CIRC
4th
• Normal voltage not ap-
plied to solenoid due
to cut line, short, or the
like.
• TCM detects as irregu-
lar by comparing tar-
get value with monitor
value.
• Harness or connectors
(Sensor circuit is open
or shorted.)
• Line pressure solenoid
valve
P1705 THROTTLE POSITION SENSOR
TM-143
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P1705 THROTTLE POSITION SENSOR
Description
INFOID:0000000001672165
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle
position sensor, etc. The actuator transmits a signal to the ECM, and ECM transmits signals to TCM with CAN
communication.
DTC Logic
INFOID:0000000001672166
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine and let it idle for 1 second.
2.
Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1705 TP SEN/CIRC A/T” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000001672167
1.
CHECK DTC OF ECM
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “SELF-DIAG RESULTS” mode for “ENGINE”.
Is any DTC detected?
YES
>> GO TO 2.
NO
>> Check DTC detected item. Refer to
EC-120, "CONSULT-III Function"
2.
CHECK DTC OF TCM
With CONSULT-III
Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is any DTC detected?
YES
>> GO TO 3.
NO
>> Check DTC detected item. Refer to
TM-112, "CONSULT-III Function (TRANSMISSION)"
3.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace the control valve with TCM. Refer to
NO
>> Repair or replace damaged parts.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P1705
TP SEN/CIRC A/T
15th
TCM does not receive
the proper accelerator
pedal position signals
(input by CAN communi-
cation) from ECM.
Harness or connectors
(Sensor circuit is open or
shorted.)
TM-144
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P1710 A/T FLUID TEMPERATURE SENSOR
P1710 A/T FLUID TEMPERATURE SENSOR
Description
INFOID:0000000001672168
The A/T fluid temperature sensor detects the A/T fluid temperature and transmits a signal to the TCM.
DTC Logic
INFOID:0000000001672169
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR”.
3.
Drive vehicle and maintain the following conditions for at least 10 minutes (total). (It is not necessary to
maintain continuously.)
With GST
Follow the procedure “With CONSULT-III”.
Is “P1710 ATF TEMP SEN/CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000001672170
1.
CHECK A/T FLUID TEMPERATURE SENSOR 1 SIGNAL
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR”.
3.
Check “ATF TEMP SE 1” and “ATF TEMP SE 2” values.
Which item is abnormal?
ATF TEMP SE 1>>GO TO 2.
ATF TEMP SE 2>>GO TO 5.
2.
CHECK A/T FLUID TEMPERATURE SENSOR 1
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P1710
ATF TEMP SEN/CIRC
10th
While running, the A/T
fluid temperature sensor
signal voltage is exces-
sively high or low.
• Harness or connectors
(Sensor circuit is open
or shorted.)
• A/T fluid temperature
sensors 1 and/or 2
VHCL/S SE-A/T
: 10 km/h (6 MPH) or more
ACCELE POSI
: More than 1.0/8
SLCT LVR POSI
: “D” position
Item name
Condition
°
C (
°
F)
Value (Approx.)
ATF TEMP SE 1
0 (32) – 20 (68) – 80 (176)
3.3 – 2.7 – 0.9 V
ATF TEMP SE 2
0 (32) – 20 (68) – 80 (176)
3.3 – 2.5 – 0.7 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст