Infiniti G37 Coupe. Manual — part 1158
HOOD SWITCH
SEC-129
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HOOD SWITCH
Description
INFOID:0000000001700057
Hood switch is built into hood lock (RH) and connected to IPDM E/R which detects the open/close condition of
hood.
Component Function Check
INFOID:0000000001700058
1.
CHECK FUNCTION
1.
Select “HOOD SW” in “Data Monitor” mode with CONSULT-III.
2.
Check the hood switch signal under the following condition.
Is the indication normal?
YES
>> Hood switch is OK.
NO
SEC-129, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001700059
1.
CHECK HOOD SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HOOD SWITCH CIRCUIT
1.
Disconnect IPDM E/R connector E9 and hood switch connector.
2.
Check continuity between IPDM E/R harness connector and hood switch harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK IPDM E/R OUTPUT
1.
Connect IPDM E/R connector.
2.
Check voltage between IPDM E/R harness connector and ground.
Test item
Condition
Status
HOOD SW
Hood
Open
ON
Close
OFF
IPDM E/R
Ground
Condition
Voltage (V)
(Approx.)
Connector
Terminal
E9
104
Ground
Hood
Open
0
Close
Battery voltage
IPDM E/R
Hood switch
Continuity
Connector
Terminal
Connector
Terminal
E9
104
E30
2
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E9
104
Ground
Not existed
SEC-130
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
HOOD SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
4.
CHECK HOOD SWITCH
SEC-130, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace hood switch.
5.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000001700060
1.
CHECK HOOD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check continuity between hood switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hood switch.
IPDM E/R
Ground
Voltage (V)
(Approx.)
Connector
Terminal
E9
104
Ground
Battery voltage
Hood switch
Condition
Continuity
Terminal
1
2
Hood switch
Press
Not existed
Release
Existed
HORN
SEC-131
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HORN
Description
INFOID:0000000001700061
Horn (high/low) is located inside of front bumper and operates when vehicle security system is in alarm phase.
Component Function Check
INFOID:0000000001700062
1.
CHECK FUNCTION
1.
Select “HORN” in “ACTIVE TEST” mode with CONSULT-III.
2.
Check the horn (high/low) operation.
Is the operation normal?
YES
>> INSPECTION END.
NO
>> Go to
SEC-131, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000001700063
1.
CHECK HORN FUNCTION
Check horn function with horn switch
Do the horns sound?
YES
>> GO TO 2.
NO
>> Go to
HRN-2, "Wiring Diagram - HORN -"
2.
CHECK HORN RELAY POWER SUPPLY
1.
Turn ignition switch ON.
2.
Perform “ACTIVE TEST” (“HORN”) with CONSULT-Ill.
3.
Check voltage between horn relay 1 and 2 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK HORN RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector E6 and horn relay 1 and 2 connector.
3.
Check continuity between IPDM E/R harness connector and horn relay 1 and 2 harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Test item
Description
HORN
ON
Horn relay 1 and 2
ON (for 20 ms)
Horn relay1/2
Ground
Condition
Voltage (V)
(Approx.)
Connector
Terminal
E11
1
Ground
HORN
Activated
0
Deactivated
Battery voltage
E18
3
Activated
0
Deactivated
Battery voltage
IPDM E/R
Horn relay 1 and 2
Continuity
Connector
Terminal
Connector
Terminal
E6
44
E11
1
Existed
45
E18
3
IPDM E/R
Ground
Continuity
Connector
Terminal
SEC-132
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
HORN
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
E6
44
Ground
Not existed
45
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст