Infiniti G37 Coupe. Manual — part 776
IN-VEHICLE SENSOR
HAC-93
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Is the inspection result normal?
YES
>> Replace unified meter and A/C amp.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000001735253
1.
CHECK IN-VEHICLE SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect in-vehicle sensor connector. Refer to
.
3.
Check continuity between in-vehicle sensor terminals.
Is the inspection result normal?
YES
>> END.
NO
>> Replace in-vehicle sensor.
In-vehicle sensor
—
Continuity
Connector
Terminal
M61
1
Ground
Not existed
Terminal
Condition
Resistance k
Ω
Temperature
°
C (
°
F)
1
2
−
15 (5)
12.73
−
10 (14)
9.92
−
5 (23)
7.80
0 (32)
6.19
5 (41)
4.95
10 (50)
3.99
15 (59)
3.24
20 (68)
2.65
25 (77)
2.19
30 (86)
1.81
35 (95)
1.51
40 (104)
1.27
45 (113)
1.07
HAC-94
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
SUNLOAD SENSOR
SUNLOAD SENSOR
Description
INFOID:0000000001675725
COMPONENT DESCRIPTION
Sunload Sensor
The sunload sensor (1) is located on the driver’s side front defroster
grille. It detects sunload entering through windshield by means of a
photo diode. The sensor converts the sunload into a current value
which is then input into the unified meter and A/C amp.
Sunload Sensor Circuit
SUNLOAD INPUT PROCESS
The unified meter and A/C amp. also equips a processing circuit which averages the variations in detected
sunload over a period of time. This prevents drastic swings in the air temperature control system operation
due to small or quick variations in detected sunload.
For example, consider driving along a road bordered by an occasional group of large trees. The sunload
detected by the sunload sensor varies whenever the trees obstruct the sunlight. The processing circuit aver-
ages the detected sunload over a period of time, so that the (insignificant) effect of the trees momentarily
obstructing the sunlight does not cause any change in the air temperature control system operation. On the
other hand, shortly after entering a long tunnel, the system recognizes the change in sunload, and the system
reacts accordingly.
Component Function Check
INFOID:0000000001675726
1.
PERFORM SELF-DIAGNOSIS STEP-2
Perform self-diagnosis STEP-2. Refer to
HAC-42, "WITHOUT LEFT AND RIGHT VENTILATION TEMPERA-
TURE SEPARATELY CONTROL SYSTEM : Diagnosis Description"
(Without left and right ventilation tempera-
ture separately control system) or
HAC-48, "WITH LEFT AND RIGHT VENTILATION TEMPERATURE
SEPARATELY CONTROL SYSTEM : Diagnosis Description"
(With left and right ventilation temperature sepa-
rately control system), see Nos. 1 to 2.
25 or
−
25 is displayed.
YES
>> Go to Diagnosis Procedure. Refer to
.
NO
>> END.
Diagnosis Procedure
INFOID:0000000001675727
1.
CHECK VOLTAGE BETWEEN SUNLOAD SENSOR AND GROUND
1.
Disconnect sunload sensor connector.
2.
Turn ignition switch ON.
JSIIA0050ZZ
RJIA4099E
SUNLOAD SENSOR
HAC-95
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
3.
Check voltage between sunload sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK CIRCUIT CONTINUITY BETWEEN SUNLOAD SENSOR AND UNIFIED METER AND A/C AMP.
1.
Turn ignition switch OFF.
2.
Disconnect unified meter and A/C amp. connector.
3.
Check continuity between sunload sensor harness connector and unified meter and A/C amp. harness
connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SUNLOAD SENSOR
1.
Reconnect sunload sensor connector and unified meter and A/C amp. connector.
2.
Check sunload sensor. Refer to
HAC-95, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace unified meter and A/C amp.
NO
>> Replace sunload sensor.
4.
CHECK CIRCUIT CONTINUITY BETWEEN SUNLOAD SENSOR AND UNIFIED METER AND A/C AMP.
1.
Turn ignition switch OFF.
2.
Disconnect unified meter and A/C amp. connector.
3.
Check continuity between sunload sensor harness connector and unified meter and A/C amp. harness
connector.
4.
Check continuity between sunload sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace unified meter and A/C amp.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000001675728
1.
CHECK SUNLOAD SENSOR
1.
Turn ignition switch ON.
2.
Check the voltage between unified meter and A/C amp. harness connector and ground.
(+)
(
−
)
Voltage
Sunload sensor
—
Connector
Terminal
M46
1
Ground
Approx. 5 V
Sunload sensor
Unified meter and A/C amp.
Continuity
Connector
Terminal
Connector
Terminal
M46
2
M67
62
Existed
Sunload sensor
Unified meter and A/C amp.
Continuity
Connector
Terminal
Connector
Terminal
M46
1
M67
46
Existed
Sunload sensor
—
Continuity
Connector
Terminal
M46
1
Ground
Not existed
HAC-96
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
SUNLOAD SENSOR
NOTE:
Select a place where sunshine directly on it when checking sunload sensor.
Is the inspection result normal?
YES
>> END.
NO
>> Replace sunload sensor.
(+)
(
−
)
Unified meter and A/C amp.
—
Connector
Terminal
M67
46
Ground
SHA930E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст