Infiniti G37 Coupe. Manual — part 1286
STARTER MOTOR
STR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
ON-VEHICLE REPAIR
STARTER MOTOR
Exploded View
INFOID:0000000001665990
REMOVAL
DISASSEMBLY
Type: S114-932
1.
“B” terminal nut
2.
“B” terminal harness
3.
Starter motor
4.
Harness clip bracket
5.
Starter motor mounting bolt
6.
Converter housing (A/T models)
Transmission case (M/T models)
7.
“S” connector
: Vehicle front
Refer to
JPBIA0147GB
STR-16
< ON-VEHICLE REPAIR >
STARTER MOTOR
Removal and Installation
INFOID:0000000001665991
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove engine undercover, using power tools.
3.
Remove road wheel and tire (Front LH), using power tools.
4.
Disconnect steering lower joint (1), then remove it. Refer to
20, "WITHOUT 4WAS : Exploded View"
21, "WITH 4WAS : Exploded View"
(With 4WAS).
5.
Remove engine mounting insulator (LH) mounting nut (Lower).
Refer to
6.
Jack up the engine front side to create clearance for removing
starter motor.
7.
Remove “B” terminal nut (A).
1.
Magnetic switch assembly
2.
Dust cover kit
3.
Shift lever set
4.
Center bracket (A)
5.
Yoke assembly
6.
Armature assembly
7.
Brush holder assembly
8.
Thrust washer
9.
Rear cover assembly
10. Shaft gear assembly
11.
Packing
12. Thrust washer
13. Center bracket (P)
14. E-ring
15. Pinion assembly
16. Pinion stopper
17. Pinion stopper clip
18. Gear case assembly
: High-temperature grease point
Refer to
for symbols not described on the above.
JPBIA0148GB
JSBIA0003ZZ
STARTER MOTOR
STR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
8.
Disconnect “S” connector (A).
9.
Remove starter motor mounting bolts (B), using power tools.
10. Remove starter motor (1) from the side of the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to tighten “B” terminal nut carefully.
Inspection
INFOID:0000000001665992
INSPECTION AFTER DISASSEMBLY
Pinion/Clutch Check
1.
Inspect pinion teeth.
• Replace pinion if teeth are worn or damaged. (Also check condition of ring gear teeth.)
2.
Inspect reduction gear teeth.
• Replace reduction gear if teeth are worn or damaged. (Also check condition of armature shaft gear
teeth.)
3.
Check to see if pinion locks in one direction and rotates smoothly in the opposite direction.
• If it locks or rotates in both directions, or unusual resistance is evident, replace.
: Vehicle front
JPBIA1187ZZ
: Vehicle front
JPBIA1218ZZ
STR-18
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Starter Motor
INFOID:0000000001665993
Type
S114-932
HITACHI make
Reduction gear type
System voltage
[V]
12
No-load
Terminal voltage
[V]
11
Current
[A]
Less than 110
Revolution
[rpm]
More than 2,700
Minimum diameter of commutator
[mm (in)]
28.0 (1.102)
Minimum length of brush
[mm (in)]
10.5 (0.413)
Brush spring tension
[N (kg, lb)]
16.2 (1.65, 3.6)
Clearance between bearing metal and armature shaft
[mm (in)]
Less than 0.2 (0.008)
Clearance between pinion front edge and pinion stopper
[mm (in)]
0.3 - 2.5 (0.012 - 0.098)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст