Infiniti G37 Coupe. Manual — part 795
INL-14
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001830716
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD) AND IGN COUNTER
Freeze Frame Data
The BCM records the following condition at the moment a particular DTC is detected.
• Vehicle Speed
• Odd Trip Meter
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
This function is not used even though it is displayed.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioner*
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
IVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
DIAGNOSIS SYSTEM (BCM)
INL-15
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
• Vehicle Condition (BCM detected condition)
IGN Counter
IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected.
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition
switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
INT LAMP
CONSULT screen terms
Description
SLEEP>LOCK
While turning BCM status from low power consumption mode to normal mode (Power supply
position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to normal mode (Power supply
position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle is stopping and selector
lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN” (From cranking up the en-
gine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emergency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply position is “OFF”.) to low power
consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply position is “LOCK”.) to low pow-
er consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steering is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
INL-16
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000001604823
WORK SUPPORT
*: Initial setting
DATA MONITOR
JPLIA0093GB
Service item
Setting item
Setting
SET I/L D-UNLCK INTCON
ON*
With the interior room lamp timer function
OFF
Without the interior room lamp timer function
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3*
15 sec.
MODE 4
30 sec.
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2
1 sec.
MODE 3
2 sec.
MODE 4*
3 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from front request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ACC RLY-F/B
[On/Off]
ACC relay feedback signal status input from ACC relay
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
DIAGNOSIS SYSTEM (BCM)
INL-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000001604824
WORK SUPPORT
*: Initial setting
DATA MONITOR
DOOR SW-DR
[On/Off]
The switch status input from driver side door switch
DOOR SW-AS
[On/Off]
The switch status input from passenger side door switch
DOOR SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW- RL
[On/Off]
NOTE:
The item is indicated, but not monitored.
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
CDL LOCK SW
[On/Off]
Lock switch status received from the door lock and unlock switch by power window
switch serial link
CDL UNLOCK SW
[On/Off]
Unlock switch status received from the door lock and unlock switch by power window
switch serial link
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch by power window switch serial
link
KEY CYL UN-SW
[On/Off]
Unlock switch status received from key cylinder switch by power window switch serial
link
TRNK/HAT MNTR
[On/Off]
The switch status input from trunk room lamp switch
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal to turn map lamp ON (Map lamp switch
is in DOOR position).
Off
Stops the interior room lamp control signal to turn map lamp OFF.
STEP LAMP TEST
On
Outputs the step lamp control signal to turn step lamp ON.
Off
Stops the step lamp control signal to turn step lamp OFF.
LUGGAGE LAMP TEST
On
Outputs the trunk room lamp control signal to turn the trunk room lamp ON.
Off
Stops the trunk room lamp control signal to turn the trunk room lamp OFF.
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ROOM LAMP BAT SAV SET
On*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст