Infiniti G37 Coupe. Manual — part 1343
ROAD TEST
TM-225
< ON-VEHICLE MAINTENANCE >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> Record the malfunction, GO TO 2.
2.
CHECK SHIFT-DOWN
During manual mode driving, is downshift from M5
→
M4
→
M3
→
M2
→
M1 performed?
With CONSULT-III
Read the value of “GEAR” and “ENGINE SPEED” with “DATA MONITOR” mode.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Record the malfunction, GO TO 3.
3.
CHECK ENGINE BRAKE
Check engine brake.
Does engine braking effectively reduce speed in M1 position?
YES
>> Check malfunction phenomena to repair or replace malfunctioning part. Refer to
NO
>> 1.
Record the malfunction.
2.
Check malfunction phenomena to repair or replace malfunctioning part. Refer to
.
TM-226
< ON-VEHICLE MAINTENANCE >
[5AT: RE5R05A]
A/T POSITION
A/T POSITION
Inspection and Adjustment
INFOID:0000000001672244
INSPECTION
1.
Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2.
Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.
3.
Shift the selector lever and check for excessive effort, sticking, noise or rattle.
4.
Confirm that the selector lever stops at each position by feeling the engagement when it is moved through
all the positions. Check whether or not the actual position the selector lever matches the position shown
by the shift position indicator and the A/T body.
5.
The method of operating the lever to individual positions cor-
rectly is shown in the figure.
6.
When selector button is pressed in “P”, “R”, or “N” position with-
out applying forward/backward force to selector lever, check but-
ton operation for sticking.
7.
Confirm that the back-up lamps illuminate only when lever is
placed in the “R” position. Confirm that the back-up lamps does
not illuminate when selector lever is pushed against “R” position
in the “P” or “N” position.
8.
Confirm that the engine can only be started with the selector
lever in the “P” and “N” positions. (With selector lever in the “P”
position, engine can be started even when selector lever is
moved forward and backward.)
9.
Make sure that A/T is locked completely in “P” position.
10. When selector lever is set to manual shift gate, make sure that manual mode is displayed on combination
meter.
Shift the selector lever to “+” and “
−
” sides, and check that set shift position changes.
ADJUSTMENT
1.
Loosen nut (
) of pivot pin (1).
2.
Place PNP switch and selector lever in “P” position.
3.
While pressing lower lever (A) toward rear of vehicle (in “P” posi-
tion direction), tighten nut (
) to specified torque. Refer to
SCIA6760E
JSDIA0134ZZ
CONTROL DEVICE
TM-227
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
CONTROL DEVICE
Exploded View
INFOID:0000000001672246
Removal and Installation
INFOID:0000000001672247
REMOVAL
1.
Disconnect lower lever of control device and control rod.
2.
Shift the selector lever to “N” position.
1.
Selector lever knob
2.
Lock pin
3.
Console finisher
4.
Selector lever position indicator
5.
Insert finisher
6.
Dust cover plate
7.
Dust cover
8.
Snap pin
9.
Plain washer
10.
Collar
11.
Control rod
12.
Pivot pin
13.
Insulator
14.
Shift lock unit
15.
Control device assembly
Refer to
JPDIA0001GB
TM-228
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL DEVICE
3.
Remove knob cover (A) below selector lever downward.
4.
Pull lock pin (1) out of selector lever knob (2).
5.
Remove selector lever knob (2).
6.
Remove console finisher assembly, rear upper console assem-
bly and console front bracket. Refer to
7.
Disconnect A/T device harness connector.
8.
Remove control device assembly.
9.
Remove the following parts if necessary.
a.
Selector lever position indicator
i.
Remove the cigarette lighter harness connector (A) from the
console finisher assembly.
ii.
Remove the insert finisher (1) from the console finisher.
iii.
Remove the selector lever position indicator.
b.
Shift lock unit
i.
Remove the shift lock unit from the control device assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000001672248
ADJUSTMENT AFTER INSTALLATION
Adjust the A/T positions after installing the control device. Refer to
TM-226, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the A/T positions after adjusting the A/T positions. Refer to
TM-226, "Inspection and Adjustment"
.
JPDIA0002ZZ
: Screw
JPDIA0050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст