Infiniti G37 Coupe. Manual — part 1360
TRANSMISSION ASSEMBLY
TM-293
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
23. Install needle bearing to transmission case.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
24. Install revolution sensor to transmission case. Tighten revolution
sensor bolt to the specified torque.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
25. As shown in the figure, use the drift to drive rear oil seal into the
rear extension until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension.
SCIA5031E
SCIA2320E
SCIA5311E
SCIA6180J
SCIA3424E
TM-294
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
28. Install parking actuator support from rear extension.
29. Install needle bearing (1) to rear extension.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
30. Install seal rings (1) to output shaft.
31. Install parking gear (1) to output shaft (2).
32. Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
look similar. (Thinner end is front side.)
SCIA3423E
SCIA6179J
JPDIA0030ZZ
JPDIA0029ZZ
SCIA5030E
TRANSMISSION ASSEMBLY
TM-295
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
33. Install bearing race to output shaft.
34. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown in the
figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
35. Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
36. Tighten rear extension assembly bolts to the specified torque.
SCIA5245E
A
: Start and finish point shall be in
the center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
SCIA5029E
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
TM-296
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
37. Install needle bearing in drum support.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
38. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
39. Install high and low reverse clutch assembly in direct clutch.
40. Using a flat-bladed screwdriver, align the drive plate.
41. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5198E
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст