Infiniti I35 (A33). Manual — part 102
SAX029
Dynamic Damper
NHAX0019S02
1.
Use new damper bands when installing.
2.
Install dynamic damper from stationary-joint side while holding
it securely.
Length:
“A”: 205 - 215 mm (8.07 - 8.46 in)
“B”: 50 mm (1.97 in)
Transaxle Side
NHAX0019S03
The joint on the transaxle side cannot be disassembled.
SFA618
Support Bearing
NHAX0019S04
I
Press bearing into retainer.
I
Install snap ring.
I
Install support bearing dust shield.
SFA694
I
Press drive shaft into bearing.
SFA444B
I
Install snap ring.
I
Install support bearing dust shield.
I
Install dust shield.
Service Data and Specifications (SDS)
DRIVE SHAFT
NHAX0020
Applied model
All
Joint type
Transaxle side
SS86
Wheel side
ZF100
Quality
Nissan genuine grease or equivalent
Grease
Capacity
g (oz)
Wheel side
115 - 125 (4.06 - 4.41)
Boot length
mm (in)
Wheel side “L
1
”
103 (4.06)
GI
MA
EM
LC
EC
FE
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-15
Applied model
All
SAX030
WHEEL BEARING (FRONT)
NHAX0021
Wheel bearing axial end play limit
mm (in)
Less than 0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
255 - 333 (26 - 34, 188 - 245)
FRONT AXLE
Service Data and Specifications (SDS) (Cont’d)
AX-16
SBR686C
Precautions
PRECAUTIONS
NHAX0022
I
When installing each rubber part, final tightening must be
carried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
Use flare nut wrench when removing or installing brake
tubes.
I
After installing removed suspension parts, check wheel
alignment.
I
Do not jack up at the trailing arm and lateral link.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NHAX0032
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST15310000
(
—
)
Drift
NT607
Install ABS sensor rotor
a: 84 mm (3.31 in) dia.
b: 96 mm (3.78 in) dia.
c: 8 mm (0.31 in)
d: 20 mm (0.79 in)
COMMERCIAL SERVICE TOOLS
NHAX0024
Tool name
Description
GG94310000
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing brake piping
a: 10 mm (0.39 in)
Drift
NT371
Install ABS sensor rotor
a: 75 mm (2.95 in) dia.
b: 62 mm (2.44 in) dia.
GI
MA
EM
LC
EC
FE
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR AXLE
Precautions
AX-17
Noise, Vibration and Harshness (NVH)
Troubleshooting
NHAX0025
Refer to “Noise, Vibration and Harshness (NVH) Troubleshooting”,
“FRONT AXLE”, AX-3.
SMA525A
On-vehicle Service
REAR AXLE PARTS
NHAX0026
Check axle and suspension parts for excessive play, wear or dam-
age.
I
Shake each rear wheel to check for excessive play.
SRA690A
REAR WHEEL BEARING
NHAX0027
I
Check axial end play.
Axial end play:
Less than 0.05 mm (0.0020 in)
I
Check that wheel hub bearings operate smoothly.
I
Check tightening torque of wheel bearing lock nut.
: 187 - 254 N·m (19 - 26 kg-m, 138 - 188 ft-lb)
I
Replace wheel bearing assembly if there is axial end play or
wheel bearing does not turn smoothly. Refer to “Wheel Hub”,
“REAR AXLE”, AX-19.
REAR AXLE
Noise, Vibration and Harshness (NVH) Troubleshooting
AX-18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст