Infiniti I35 (A33). Manual — part 112
SBR646
SBR868C
8.
Insert piston seal into groove on cylinder body.
9.
With piston boot fitted to piston, insert piston boot into groove
on cylinder body and fit piston by turning it clockwise with long
nose pilers, or suitable tool.
SBR027D
10. Fit toggle lever, return spring and cable guide.
SBR306E
11. Adjust the piston to the right angle as shown in the figure.
SBR307E
Installation
NHBR0043
CAUTION:
I
Refill with new brake fluid “DOT 3”.
I
Never reuse drained brake fluid.
1.
Install caliper assembly.
I
As shown in the figure, align the piston’s concave to the pad’s
convex, then install the cylinder body to the torque member.
2.
Install brake hose to caliper securely.
3.
Install all parts and secure all bolts.
4.
Bleed air. Refer to “Bleeding Brake System”, BR-8.
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
REAR DISC BRAKE
Assembly (Cont’d)
BR-33
Components
NHBR0128
SBR892E
SBR025D
Removal and Installation
NHBR0129
1.
To remove parking brake cable, first remove center console.
2.
To remove parking brake pedal, remove lower instrument
panel on driver side.
3.
Disconnect warning switch connector.
4.
Remove bolts, slacken off and remove adjusting nut.
5.
Remove lock plate and disconnect cable.
Inspection
NHBR0130
1.
Check parking brake pedal assembly for wear or other dam-
age. Replace if necessary.
2.
Check wires for discontinuity or deterioration. Replace if nec-
essary.
3.
Check warning lamp and switch. Replace if necessary.
4.
Check parts at each connecting portion and, if found deformed
or damaged, replace.
PARKING BRAKE CONTROL
Components
BR-34
SBR264B
Adjustment
=NHBR0131
Pay attention to the following points after adjustment.
1)
There is no drag when control lever is being released.
2)
Be sure that toggle lever returns to stopper when parking brake
pedal is released.
1.
Loosen parking brake cable.
2.
Depress brake pedal fully more than five times.
3.
Operate control pedal 10 times or more with a full stroke [203.5
mm (8.01 in)].
4.
Adjust control lever or pedal by turning adjusting nut.
5.
Depress pedal with specified amount of force. Check lever
stroke and ensure smooth operation.
Number of notches:
4 - 5 [196 N (20 kg, 44 lb)]
6.
Bend warning lamp switch plate. Warning lamp should come
on when lever is depressed “A” notches. It should go off when
the lever is fully released.
Number of “A” notches: 1
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
PARKING BRAKE CONTROL
Adjustment
BR-35
Purpose
NHBR0048
The ABS consists of electronic and hydraulic components. It allows for control of braking force so that lock-
ing of the wheels can be avoided.
The ABS:
1) Ensures proper tracking performance through steering wheel operation.
2) Enables obstacles to be avoided through steering wheel operation.
3) Ensures vehicle stability by preventing flat spins.
ABS (Anti-Lock Brake System) Operation
NHBR0049
I
When the vehicle speed is less than 10 km/h (6 MPH) this system does not work.
I
The Anti-Lock Brake System (ABS) has self-test capabilities. The system turns on the ABS warning lamp
for 1 second after turning the ignition switch ON. The system performs another test the first time the vehicle
reaches 6 km/h (4 MPH). A mechanical noise may be heard as the ABS performs a self-test. This is a
normal part of the self-test feature. If a malfunction is found during this check, the ABS warning lamp will
come on.
I
During ABS operation, a mechanical noise may be heard. This is a normal condition.
ABS Hydraulic Circuit
NHBR0050
SBR984D
1.
Inlet solenoid valve
2.
Outlet solenoid valve
3.
Reservoir
4.
Pump
5.
Motor
6.
Inlet valve
7.
Outlet valve
8.
Bypass check valve
9.
Damper
DESCRIPTION
TCS
Purpose
BR-36
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст