Infiniti I35 (A33). Manual — part 394
I
from terminal 18 of the front wiper switch
I
through terminal 17 of the front wiper switch, and
I
through body grounds E11, E22 and E53.
With power and ground supplied, the front washer motor operates.
When the lever is pulled to the WASH position for one second or more, the front wiper motor operates at low
speed for approximately 3 seconds to clean windshield. This feature is controlled by the wiper amplifier in the
same manner as the intermittent operation.
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
FRONT WIPER AND WASHER
System Description (Cont’d)
EL-177
Wiring Diagram — WIPER —
NHEL0058
MEL310O
FRONT WIPER AND WASHER
Wiring Diagram — WIPER —
EL-178
SEL543TA
Removal and Installation
NHEL0060
WIPER ARMS
NHEL0060S01
1.
Prior to wiper arm installation, turn on front wiper switch to
operate front wiper motor and then turn it “OFF” (Auto Stop).
2.
Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L
1
” & “L
2
” immediately before
tightening nut.
3.
Eject washer fluid. Turn on front wiper switch to operate front
wiper motor and then turn it “OFF”.
4.
Ensure that wiper blades stop within clearance “L
1
” & “L
2
”.
Clearance “L
1
”: 48 - 64 mm (1.89 - 2.52 in)
Clearance “L
2
”: 40 - 56 mm (1.57 - 2.20 in)
I
Tighten wiper arm nuts to specified torque.
Front wiper: 21 - 26 N·m (2.1 - 2.7 kg-m, 16 - 19 ft-lb)
SEL024J
I
Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm loose-
ness.
WIPER LINKAGE
NHEL0060S02
MEL063R
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
FRONT WIPER AND WASHER
Removal and Installation
EL-179
Removal
NHEL0060S0201
1.
Remove 4 bolts that secure front wiper motor.
2.
Detach front wiper motor from wiper linkage at ball joint.
3.
Remove wiper linkage.
Be careful not to break ball joint rubber boot.
Installation
NHEL0060S0202
I
Grease ball joint portion before installation.
1.
Installation is the reverse order of removal.
SEL241P
Washer Nozzle Adjustment
NHEL0061
I
Adjust washer nozzle with suitable tool as shown in the figure
at left.
Adjustable range:
±
10°
SEL544T
Unit: mm (in)
*1
341 (13.43)
*5
154 (6.06)
*2
286 (11.26)
*6
203 (7.99)
*3
285 (11.22)
*7
382 (15.04)
*4
152 (5.98)
*8
385 (15.16)
*: The diameters of these circles are less than 80 mm (3.15 in).
MEL377K
Washer Tube Layout
NHEL0062
FRONT WIPER AND WASHER
Removal and Installation (Cont’d)
EL-180
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст