Infiniti QX50 (2021 year). Manual in english — page 7

WARNING

When the high fluid temperature protec-
tion mode operation occurs, vehicle speed
may be gradually reduced. The reduced
speed may be lower than other traffic,
which could increase the chance of a colli-
sion. Be especially careful when driving. If
necessary, pull to the side of the road at a
safe place and allow the transmission to
return to normal operation; or have it re-
paired if necessary.

Engine hot Power reduced

This engine has a high fluid temperature pro-
tection mode. If the fluid temperature be-
comes too high (for example, climbing steep
grades in high temperatures with heavy
loads, such as when towing a trailer), engine
power and, under some conditions, vehicle
speed will be decreased automatically to re-
duce the chance of engine damage. Vehicle
speed can be controlled with the accelerator
pedal, but the engine and vehicle speed may
be reduced.

WARNING

When the high fluid temperature protec-
tion mode operation occurs, vehicle speed
may be gradually reduced. The reduced
speed may be lower than other traffic,
which could increase the chance of a colli-
sion. Be especially careful when driving. If
necessary, pull to the side of the road at a
safe place and allow the engine to return to
normal operation; or have it repaired if
necessary.

Engine Malfunction: Power Reduced
Service now

This warning appears when the engine is not
operating under normal conditions. If this
warning comes on, have the system checked.

It is recommended that you visit an INFINITI
retailer for this service.

Engine Malfunction Service now

This warning appears when there is a prob-
lem with the engine. If this warning comes on,
have the system checked. It is recommended
that you visit an INFINITI retailer for this
service.

Engine Stalled: Stop safely

This message appears 30 seconds before the
vehicle is shut down due to an above normal
operating exhaust temperature. The Mal-
function Indicator Light (MIL) and malfunc-
tion warning (red) will illuminate. Have the
system checked. It is recommended that you
visit an INFINITI retailer immediately for this
service.

Service CVT (AT) Power reduced

This transmission has a high fluid tempera-
ture protection mode. If the fluid temperature
becomes too high (for example, climbing
steep grades in high temperatures with heavy
loads, such as when towing a trailer), engine
power and, under some conditions, vehicle
speed will be decreased automatically to re-
duce the chance of transmission damage.
Vehicle speed can be controlled with the ac-
celerator pedal, but the engine and vehicle
speed may be reduced.

Instruments and controls

2-25

WARNING

When the high fluid temperature protec-
tion mode operation occurs, vehicle speed
may be gradually reduced. The reduced
speed may be lower than other traffic,
which could increase the chance of a colli-
sion. Be especially careful when driving. If
necessary, pull to the side of the road at a
safe place and allow the transmission to
return to normal operation; or have it re-
paired if necessary.

Blind Spot Warning (BSW)
indicator

This indicator appears when the BSW system
is engaged.

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-45) and “Blind Spot
Intervention® (BSI)” (P. 5-54).

Cruise control indicator

This indicator shows the cruise control sys-
tem status.

When cruise control is activated, a green
circle will appear to indicate it is set. The
vehicle information display will also display
the speed the cruise control was set at. If you
accelerate past the set speed, the speed will
blink until you either cancel cruise control or

go back to the set speed. If cruise control is on
and canceled, the speed will be displayed to
show the speed the vehicle will return to if the
resume button is activated.

Currently not available

This message appears when the VDC system
is turned off. The following systems (if so
equipped) will be turned off automatically:
BSI system, DCA system, LDP system and
the ProPILOT Assist system.

For additional information, see “Vehicle Dy-
namic Control (VDC)” (P. 5-154), “Blind Spot
Intervention® (BSI)” (P. 5-54), “Distance
Control Assist (DCA)” (P. 5-106), “Lane De-
parture Prevention (LDP)” (P. 5-40) and/or
“ProPILOT Assist” (P. 5-77).

Distance Control Assist
(DCA) ON / Lane Departure
Prevention (LDP) ON / Blind
Spot Intervention® (BSI) ON
/ ProPILOT Assist status
indicator

This indicator shows when the DCA/LDP/
BSI/ProPILOT system is engaged.

For additional information, see “Distance
Control Assist (DCA)” (P. 5-106), Lane De-
parture Prevention (LDP) (P. 5-40), Blind

Spot Intervention® (BSI) (P. 5-54), ProPILOT
Assist (P. 5-77).

Lane Departure Warning
(LDW)/Lane Departure
Prevention (LDP) indicator

This indicator shows when the LDW/LDP
systems are engaged.

For additional information, see “Lane Depar-
ture Warning (LDW)” (P. 5-35) and “Lane
Departure Prevention (LDP) (P. 5-40).

Malfunction

This warning appears when one or more of
the following systems (if so equipped) is not
functioning properly:
• Blind Spot Intervention® (BSI)
• Blind Spot Warning (BSW)
• Distance Control Assist (DCA)
• Forward Emergency Braking (FEB) with

Pedestrian Detection

• Lane Departure Warning (LDW)
• Lane Departure Prevention (LDP)
• Predictive

Forward

Collision

Warning

(PFCW)

• ProPilot Assist
• Rear Cross Traffic Alert (RCTA)
• Traffic Sign Recognition (TSR)

2-26

Instruments and controls

If one or more of these warning appears,
have the system checked. It is recommended
that you visit an INFINITI retailer for this
service.

Not Available Bad Weather

This message may appear when the Steering
Assist system is engaged.

Under the following condition, the Steering
Assist system is automatically canceled:
• When the wiper (HI) operates

The system will be available when the above
condition no longer exists.

Not Available: High Camera Temp

This message appears when the camera de-
tects an interior temperature of more than
104°F (40°C).

For additional information, see “Blind Spot
Intervention® (BSI)” (P. 5-54) , “Lane Depar-
ture Warning (LDW)” (P. 5-35), “Lane Depar-
ture Prevention (LDP)” (P. 5-40) or “Traffic
Sign Recognition (TSR)” (P. 5-32).

Not Available Poor Road Conditions

This message may appear when the ProPI-
LOT Assist system, the Blind Spot Interven-
tion® (BSI) system, the Lane Departure Pre-
vention (LDP) system or the Distance Control
Assist (DCA) system is engaged.

Under the following conditions, the ProPI-
LOT Assist system, the Blind Spot Interven-
tion® (BSI) system, the Lane Departure Pre-
vention (LDP) system, or the Distance
Control Assist (DCA) system, is automatically
canceled:
• When the VDC operates
• When a wheel slips

The above system cannot be used in some
situations (VDC operates and wheel slips).

Not Available Seat Belt Not
Fastened

This message may appear when the Intelli-
gent Cruise Control (ICC) (with ProPILOT
Assist) system is engaged.

Under the following condition, the ICC (with
ProPILOT Assist) system is automatically
canceled:
• When the driver’s seat belt is not fastened

The above system cannot be used when the
driver’s seat belt is not fastened.

Not Available Visibility is Impaired

This message may appear when the Intelli-
gent Cruise Control (ICC) (with ProPILOT
Assist) system is engaged.

Under the following conditions, The ICC
(with ProPILOT Assist) system is automati-
cally canceled:
• The camera area of the windshield is

fogged up or covered with dirt, water
drops, ice, snow, etc.

• Strong light, such as sunlight or high beams

from oncoming vehicles, enter the front
camera

The system will be available when the above
conditions no longer exist.

If the warning message continues to appear,
stop the vehicle in a safe location, turn the
engine off, and clean the windshield.

ProPILOT Assist indicators

These indicators show the ProPILOT Assist
system status.

For additional information, see “ProPILOT
Assist” (P. 5-77).

Rear Automatic Braking
(RAB) indicator

This indicator appears to indicate the status
of the Rear Automatic Braking (RAB) system.
For additional information, see “Rear Auto-
matic Braking (RAB)” (P. 5-119).

Instruments and controls

2-27

Speed Limit Sign indicator

This message may appear when the Traffic
Sign Recognition system is engaged.

For additional information, see “Traffic Sign
Recognition (TSR)” (P. 5-32).

Steering Assist Alert

This message may appear when the Steering
Assist system is engaged.

It will be displayed under the following
condition:
• When not holding the steering wheel or

when there is no steering wheel operation

Please hold on the steering wheel immedi-
ately. When the steering operation is de-
tected, the warning turns off and the steering
assist function is automatically restored.

Steering Assist Not Available:
Cannot Detect Lane

This message may appear when the Steering
Assist system is engaged.

Under the following conditions, the Steering
Assist system is automatically canceled:

• When lane markers in the traveling lane

cannot be correctly detected for a period of
time due to such items as a snow rut, re-
flection of light on a rainy day or several
unclear lane markers are present

If you want to use the Steering Assist system
again, cancel the ProPILOT Assist system
and set it again when lane markers are clearly
visible.

Steering Assist status

This indicator appears when the Steering As-
sist system is engaged.

For additional information, see “ProPILOT
Assist” (P. 5-77).

System fault See Owner’s Manual

This warning appears if there is a malfunction
in the Rear Automatic Braking (RAB) system.
For additional information, see “Rear Auto-
matic Braking (RAB)” (P. 5-119).

Unavailable: Front Radar Blocked

This message appears when the Distance
Control Assist (DCA), Forward Emergency
Braking (FEB) with Pedestrian Detection, or
Predictive

Forward

Collision

Warning

(PFCW) systems become unavailable be-
cause the front radar is obstructed. For addi-
tional information, see “Distance Control As-
sist (DCA)” (P. 5-106), “Forward Emergency
Braking (FEB) with Pedestrian Detection”
(P. 5-123), or “Predictive Forward Collision
Warning (PFCW)” (P. 5-133).

Unavailable: Side Radar Obstruction

This message appears when one of the fol-
lowing systems (if so equipped) becomes un-
available because a radar blockage is de-
tected.
• Blind Spot Intervention® (BSI)
• Blind Spot Warning (BSW)
• Rear Cross Traffic Alert (RCTA)

For additional information, see “Starting and
driving” (P. 5-4).

2-28

Instruments and controls

Vehicle ahead detection
indicator

This indicator shows when the following sys-
tems (if so equipped) are engaged and have
detected a vehicle:
• Distance Control Assist (DCA)
• Forward Emergency Braking (FEB) with

Pedestrian Detection

• Predictive

Forward

Collision

Warning

(PFCW)

For additional information, see “Distance
Control Assist (DCA)” (P. 5-106), “Forward
Emergency Braking (FEB) with Pedestrian
Detection” (P. 5-123) or “Predictive Forward
Collision Warning (PFCW)” (P. 5-133)

Your vehicle has two types of security
systems:
• Vehicle security system
• INFINITI Vehicle Immobilizer System

VEHICLE SECURITY SYSTEM

The vehicle security system provides visual
and audible alarm signals if someone opens
the doors, liftgate or hood when the system is
armed. It is not, however, a motion detection
type system that activates when a vehicle is
moved or when a vibration occurs.

The system helps deter vehicle theft but can-
not prevent it nor can it prevent the theft of
interior or exterior vehicle components in all
situations. Always secure your vehicle even if
parking for a brief period. Never leave your
Intelligent Key in the vehicle, and always lock
the vehicle when unattended. Be aware of
your surroundings, and park in secure, well-lit
areas whenever possible.

Many devices offering additional protection,
such as component locks, identification
markers, and tracking systems, are available
at auto supply stores and specialty shops. An
INFINITI retailer may also offer such equip-
ment. Check with your insurance company to
see if you may be eligible for discounts for
various theft protection features.

How to arm the vehicle security
system

1. Close all windows and the moonroof (if so

equipped).

(The system can be armed even

if the windows and moonroof are open.)

2. Remove the Intelligent Key from the

vehicle.

LIC0661

SECURITY SYSTEMS

Instruments and controls

2-29

3. Close all doors, hood and liftgate. Lock all

doors. The doors can be locked with the
Intelligent Key, door handle request
switch, or power door lock switch.

4. Confirm that the

security indicator

light stays on for about 30 seconds. The
vehicle security system is now pre-armed.
The vehicle security system will automati-
cally shift into the armed phase. The
security light begins to flash once every
three seconds. If during the pre-armed
phase one of the following occurs, the
system will not arm:

• Any door is unlocked with the Intelligent

Key or door request switch.

• Ignition switch is placed in AUTO ACC or

ON position.

•

Even when the driver and/or passengers
are in the vehicle, the system will activate
with all the doors, hood and liftgate locked
with the ignition switch placed in the
LOCK position. When placing the ignition
switch in the AUTO ACC or ON position,
the system will be released.

Vehicle security system activation

The vehicle security system will give the fol-
lowing alarm:
• The turn signals blink and the horn sounds

intermittently.

• The alarm automatically turns off after a

period of time. However, the alarm reacti-
vates if the vehicle is tampered with again.
The alarm can be shut off by pressing the

button on the Intelligent Key.

The alarm is activated by:
• Opening the door or liftgate without using

the Intelligent Key (even if the door is un-
locked by releasing the door inside lock
switch).

How to stop an activated alarm

The alarm stops only by unlocking the driver’s
door or the liftgate by pressing the
button on the Intelligent Key or pushing the
request switch on the driver's or passenger's
door with the Intelligent Key in range of the
door handle.

INFINITI VEHICLE IMMOBILIZER
SYSTEM

The INFINITI Vehicle Immobilizer System will
not allow the engine to start without the use
of a registered INFINITI Vehicle Immobilizer
System key.

If the engine fails to start using a registered
INFINITI Vehicle Immobilizer System key (for
example, when interference is caused by an-
other INFINITI Vehicle Immobilizer System
key, an automated toll road device or auto-
matic payment device on the key ring), restart
the engine using the following procedures:

1. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position, and wait approximately
10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the de-

vice (which may have caused the interfer-
ence)

separate

from

the

registered

INFINITI Vehicle Immobilizer System key.

If the no start condition re-occurs, INFINITI
recommends placing the registered INFINITI

2-30

Instruments and controls

Vehicle Immobilizer System key on a separate
key ring to avoid interference from other
devices.

FCC Notice:

For USA:

This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.

NOTE:

Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user's authority to oper-
ate the equipment.

For Canada:

This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.

Security indicator light

The security indicator light blinks whenever
the ignition switch is placed in the OFF or
LOCK position.

This function indicates the INFINITI Vehicle
Immobilizer System is operational.

If the INFINITI Vehicle Immobilizer System is
malfunctioning, the light will remain on while
the ignition switch is placed in the ON
position.

If the light still remains on and/or the engine
will not start, seek service for the INFINITI
Vehicle Immobilizer System service as soon
as possible. Please bring all registered keys
that you have. It is recommended that you
visit an INFINITI retailer for this service.

LIC0474

Instruments and controls

2-31

SWITCH OPERATION

WARNING

In freezing temperatures the washer solu-
tion may freeze on the windshield and ob-
scure your vision which may lead to an ac-
cident. Warm the windshield with the
defroster before you wash the windshield.

CAUTION

•

Do not operate the washer continuously
for more than 30 seconds.

•

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

•

Do not fill the windshield-washer fluid
reservoir with windshield-washer fluid
concentrates at full strength. Some
methyl alcohol based windshield-washer
fluid concentrates may permanently
stain the grille if spilled while filling the
windshield-washer fluid reservoir.

•

Pre-mix windshield-washer fluid con-
centrates with water to the manufactur-
er’s recommended levels before pouring
the fluid into the windshield-washer
fluid

reservoir.

Do

not

use

the

windshield-washer fluid reservoir to mix
the windshield-washer fluid concentrate
and water.

NOTE:

If the windshield wiper operation is inter-
rupted by snow or ice, the wiper may stop
moving to protect its motor. If this occurs,
turn the wiper switch to the OFF position
and remove the snow or ice that is on and
around the wiper arms. In approximately 1
minute, turn the switch on again to operate
the wiper.

The windshield wiper and washer operates
when the ignition switch is in the ON position.

Push the lever down to operate the wiper at
the following speed:

䊊

1

Intermittent — intermittent operation can
be adjusted by turning the knob toward

O

A

(slower) or

O

B

(faster). Also, the inter-

mittent operation speed varies in accor-
dance with the vehicle speed. (For ex-
ample, when the vehicle speed is high, the
intermittent operation speed will be

LIC4019

Type A (if so equipped)

LIC3097

Type B (if so equipped)

WIPER AND WASHER SWITCH

2-32

Instruments and controls

faster.) Further, if so equipped, the rain-
sensing feature will adjust the speed of
the intermittent operation. For additional
information,

see

“Rain-sensing

auto

wiper system” (P. 2-33).

䊊

2

Low — continuous low speed operation

䊊

3

High — continuous high speed operation

Push the lever up

O

4

to have one sweep

operation of the wiper.

Pull the lever toward you

O

5

to operate the

washer. The wiper will also operate several
times.

Drip Wipe

A brief period of time after using the washer,
the wiper will perform a one sweep operation
automatically

to

clear

any

remaining

windshield-washer fluid from the windshield.

NOTE:

The Drip Wipe feature may be disabled. For
additional information, refer to the separate
INFINITI InTouch™ Owner’s Manual.

RAIN-SENSING AUTO WIPER
SYSTEM (if so equipped)

CAUTION

•

Do not touch the rain sensor and around
it when the wiper switch is in the AUTO
position and the ignition switch is in the
ON position. The wipers may operate
unexpectedly and cause an injury or may
damage a wiper.

•

The rain-sensing auto wipers are in-
tended for use during rain. If the switch is
left in the AUTO position, the wipers
may operate unexpectedly when dirt,
fingerprints, oil film or insects are stuck
on or around the sensor. The wipers may
also operate when exhaust gas or mois-
ture affect the rain sensor.

•

When the windshield glass is coated with
water repellent, the speed of the rain-
sensing auto wipers may be higher even
though the amount of the rainfall is
small.

•

Be sure to turn off the rain-sensing auto
wiper system when you use a car wash.

•

The rain-sensing auto wipers may not
operate if rain does not hit the rain sen-
sor even if it is raining.

•

Using Genuine NISSAN wiper blades is
recommended for proper operation of
the rain-sensing auto wiper system. For
additional information, see “Windshield
wiper blades” (P. 8-17).

The rain-sensing auto wiper system can au-
tomatically turn on the wipers and adjust the
wiper speed depending on the rainfall and the
vehicle speed by using the rain sensor located
on the upper part of the windshield.

LIC3817

Instruments and controls

2-33

To set the rain-sensing auto wiper system,
place the lever in the AUTO position

O

1

. The

wiper will sweep once while the ignition
switch is in the ON position.

The rain sensor sensitivity level can be ad-
justed by turning the knob toward the front

O

2

(High) or toward the rear

O

3

(Low).

– High — High sensitive operation
– Low — Low sensitive operation

To turn the rain-sensing auto wiper system
off, rotate the lever to the OFF position, or
rotate the lever to the low or high position.

The rain-sensing feature may be disabled.
For additional information, refer to the sepa-
rate INFINITI InTouch™ Owner’s Manual.

REAR SWITCH OPERATION

WARNING

In freezing temperatures the washer solu-
tion may freeze on the rear window and
obscure your vision which may lead to an
accident. Warm the rear window with the
defroster before you wash the rear
window.

CAUTION

•

Do not operate the washer continuously
for more than 30 seconds.

•

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

•

Do not fill the windshield-washer fluid
reservoir with windshield-washer fluid
concentrates at full strength. Some
methyl alcohol based windshield-washer
fluid concentrates may permanently
stain the grille if spilled while filling the
windshield-washer fluid reservoir.

•

Pre-mix windshield-washer fluid con-
centrates with water to the manufactur-
er’s recommended levels before pouring
the fluid into the windshield-washer
fluid

reservoir.

Do

not

use

the

windshield-washer fluid reservoir to mix
the windshield-washer fluid concentrate
and water.

LIC4244

2-34

Instruments and controls

NOTE:

If the rear window wiper operation is inter-
rupted by snow, etc., the wiper may stop
moving to protect its motor. If this occurs,
turn the wiper switch to OFF and remove the
snow, etc. on and around the wiper arms.
After about 1 minute, turn the switch on
again to operate the wiper.

The rear window wiper and washer operate
when the ignition switch is in the ON position.
Turn the switch clockwise from the OFF po-
sition to operate the wiper.

䊊

1

Intermittent — intermittent operation (not
adjustable)

䊊

2

Low — continuous low speed operation

Push the switch forward

O

3

to operate the

washer. The wiper will also operate several
times.

If the windshield wipers are on and the ve-
hicle is placed in R (Reverse) the rear wiper
will automatically turn on while the vehicle
remains in R (Reverse).

NOTE:

The Reverse Link feature may be disabled.
For additional information, refer to the
separate INFINITI InTouch™ Owner’s Manual.

To defrost the rear window glass and outside
mirrors (if so equipped), place the ignition
switch in the ON position and push the rear
window defroster switch on. The rear win-
dow defroster indicator light comes on. Push
the switch again to turn the defroster off.

The rear window defroster automatically
turns off after approximately 15 minutes.

To turn on the wiper deicer (if so equipped),
place the ignition switch in the ON position
and push the wiper deicer switch on. The
wiper deicer indicator light comes on. Push
the switch again to turn the deicer off.

CAUTION

When cleaning the inner side of the rear
window, be careful not to scratch or dam-
age the rear window defroster.

NOTE:

The top and bottom few rows of wires on the
rear window are not part of the rear window
defroster system. These wires make up the
antenna for the audio system.

LIC3816

REAR WINDOW DEFROSTER, OUTSIDE
MIRROR DEFROSTER (if so equipped), AND
WIPER DEICER (if so equipped) SWITCH

Instruments and controls

2-35

HEADLIGHT CONTROL SWITCH

Lighting

䊊

1

Rotate the switch to the

position,

and the front parking, tail, license plate,
and instrument panel lights will come on.

䊊

2

Rotate the switch to the

position,

and the headlights will come on and all
the other lights remain on.

CAUTION

Use the headlights with the engine running
to avoid discharging the vehicle battery.

Autolight system

The autolight system allows the headlights to
turn on and off automatically. The autolight
system can:
• Turn on the headlights, front parking, tail,

license plate and instrument panel lights
automatically when it is dark.

• Turn off all the lights (except daytime run-

ning lights) when it is light.

• Keep all the lights on for a period of time

after you place the ignition switch in the
OFF position and all doors are closed.

NOTE:
Autolight activation sensitivity and the
time delay for autolight shutoff can be
adjusted. For additional information, re-
fer to the separate INFINITI InTouch™
Owner’s Manual.

To turn on the autolight system:

1. Turn the headlight switch to the AUTO

position

O

1

.

2. Place the ignition switch in the ON

position.

3. The autolight system automatically turns

the headlights on and off.

Initially, if the ignition switch is placed in the
OFF position and a door is opened and left
open, the headlights remain on for a period of
time. If another door is opened while the
headlights are on, then the timer is reset.

The headlights will turn on automatically at
twilight or in rainy weather (when the wind-
shield wiper is operated continuously).

If the ignition switch is pushed to the OFF
position and one of the doors is opened and
this condition is continued, the headlights re-
main on for 5 minutes.

To turn the autolight system off, turn the
switch to the OFF,

, or

position.

LIC3818

LIC3819

HEADLIGHT SWITCH

2-36

Instruments and controls

Be sure you do not put anything on top of the
autolight sensor located in the top side

O

1

of

the instrument panel. The autolight sensor
controls the autolight; if it is covered, the
autolight sensor reacts as if it is dark out and
the headlights will illuminate. If this occurs
while parked with the engine off and the ig-
nition switch placed in the ON position, your
vehicle's battery could become discharged.

Headlight beam select

䊊

1

To select the high beam function, rotate
the headlight control switch to the
position, then push the lever forward.
The high beam lights come on and the

light illuminates.

䊊

2

Pull the lever back to select the low beam.

䊊

3

Pulling and releasing the lever flashes the
headlight high beams on and off.

High Beam Assist

The High Beam Assist system will operate
when the vehicle is driven at speeds of ap-
proximately 25 mph (40 km/h) and above. If
an oncoming vehicle or leading vehicle ap-
pears in front of your vehicle when the head-
light high beam is on, the headlight will be
switched to the low beam automatically.

WARNING

•

The High Beam Assist system is a conve-
nience but it is not a substitute for safe
driving operation. The driver should re-
main alert at all times, ensure safe driv-
ing practices and switch the high beams
and low beam manually when necessary.

•

The high beam or low beam may not
switch automatically under the follow-
ing conditions. Switch the high beam and
low beam manually.

–

During bad weather (rain, fog, snow,
wind, etc.).

–

When a light source similar to a head-
light or tail light is in the vicinity of the
vehicle.

LIC2237

LIC3820

Instruments and controls

2-37

–

When the headlights of the oncoming
vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials on
the lights, or when the light beam is
out of position.

–

When there is a sudden, continuous
change in brightness.

–

When driving on a road that passes
over rolling hills, or a road that has
level differences.

–

When driving on a road with many
curves.

–

When a sign or mirror-like surface is
reflecting intense light towards the
front of the vehicle.

–

When the container, etc. being towed
by a leading vehicle is reflecting in-
tense light.

–

When a headlight on your vehicle is
damaged or dirty.

–

When the vehicle is leaning at an
angle due to a punctured tire, being
towed, etc.

•

The timing of switching the low beam
and high beam may change under the fol-
lowing situations.

–

The brightness of the headlights of
the oncoming vehicle or leading
vehicle.

–

The movement and direction of the
oncoming vehicle and the leading
vehicle.

–

When only one light on the oncoming
vehicle or the leading vehicle is
illuminated.

–

When the oncoming vehicle or the
leading vehicle is a two-wheeled
vehicle.

–

Road conditions (incline, curve, the
road surface, etc.).

–

The number of passengers and the
amount of luggage.

High Beam Assist operation

To activate the High Beam Assist system,
turn the headlight switch to the AUTO posi-
tion

O

1

and push the lever forward

O

2

(high

beam position). The High Beam Assist indica-
tor light in the meter will illuminate while the
headlights are turned on.

If the High Beam Assist indicator light does
not illuminate in the above condition, it may
indicate that the system is not functioning
properly. Have the system checked. It is rec-
ommended that you visit an INFINITI retailer
for this service.

LIC3819

2-38

Instruments and controls

When the vehicle speed lowers to less than
approximately 16 mph (25 km/h), the head-
light uses the low beam.

To turn off the High Beam Assist system, turn
the headlight switch to the

position or

select the low beam position by placing the
lever in the neutral position.

Ambient image sensor maintenance

The ambient image sensor

O

1

for the High

Beam Assist system is located in front of the
inside mirror. To maintain the proper opera-
tion of the High Beam Assist system and
prevent a system malfunction, be sure to ob-
serve the following:
• Always keep the windshield clean.
• Do not attach a sticker (including transpar-

ent material) or install an accessory near
the ambient image sensor.

• Do not strike or damage the areas around

the ambient image sensor. Do not touch the
sensor lens that is located on the ambient
image sensor.

If the ambient image sensor is damaged due
to an accident, it is recommended that you
visit an INFINITI retailer.

Battery saver system

The battery saver system automatically turns
off the ignition after a period of time when
the ignition switch is left in the AUTO ACC or
ON position.

The battery saver system automatically turns
off the following lights after a period of time
when the ignition switch is placed in the OFF
position and the doors are closed:
• Headlights, when the headlight switch is in

the

or

position

• Interior lights, when left in the ON position

CAUTION

Even though the battery saver feature au-
tomatically turns off the headlights after a
period of time, you should turn the head-
light switch to the OFF position when the
engine is not running to avoid discharging
the vehicle battery.

LIC3821

LIC4259

Instruments and controls

2-39

Adaptive Front lighting System
(AFS) (if so equipped)

The Adaptive Front lighting System (AFS) will
automatically adjust the headlights (low
beam) toward the turning direction to im-
prove the driver’s view. When the headlight
switch is ON and the driver operates the
steering wheel in a turn, the AFS system will
be activated.

The AFS will operate:
• when the headlight switch is ON.
• when the shift lever is in any position other

than P (Park) or R (Reverse).

• when the vehicle is driven at above 16 mph

(25 km/h) for the left-side headlight. Note
that the right-side low beam headlight will
swivel but the left side will not swivel when
the vehicle is at a stop and the steering
wheel is turned. The vehicle must attain a
speed above 16 mph (25 km/h) before AFS
activates the left-side headlight.

AFS will also adjust the headlight to a proper
axis automatically, depending on the number
of occupants in the vehicle, the load the ve-
hicle is carrying and the road conditions.

If the AFS OFF indicator blinks or the vehicle
information display shows an AFS system
error message after the ignition switch has
been pushed to the ON position, this may
indicate that the AFS is not functioning prop-
erly. Have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service. When the engine is started, the head-
lights will vibrate to check the system condi-
tion. This is not a malfunction.

Automatic headlight aiming control
(if so equipped)

Your vehicle is equipped with an automatic
headlight levelling system. The headlight axis
is controlled automatically.

INFINITI recommends that you consult the
local regulations on the use of lights.

LED DAYTIME RUNNING LIGHTS
(DRL) SYSTEM

The LED portion of the headlights automati-
cally illuminate at 100% intensity when the
engine is started and the parking brake re-
leased. The LED Daytime Running Lights
(DRL) system operates with the headlight
switch in the OFF position. When you turn
the headlight switch to the

position for

full illumination, the LED lights switch from
LED DRL system to the park function.

If the parking brake is applied before the
engine is started, the LED DRL system does
not illuminate. The LED DRL system illumi-
nates when the parking brake is released. The
LED DRL system will remain on until the
ignition switch is placed in the OFF position.

It is necessary at dusk to turn the headlight
switch on for interior controls and switches
to illuminate, as those remain off while the
switch is in the OFF position.

WARNING

When the LED DRL system is active, tail
lights on your vehicle are not on. It is nec-
essary at dusk to turn on your headlights.
Failure to do so could cause an accident
injuring yourself and others.

2-40

Instruments and controls