Infiniti FX35, FX50 (S51). Manual — part 283
BRM-10
< REMOVAL AND INSTALLATION >
BODY COMPONENT PARTS
NOTE:
For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
10. Upper inner front pillar assembly (RH
& LH)
11.
Front roof rail brace (RH & LH)
12. Inner center pillar (RH & LH)
13. Outer sill (RH & LH)
14. Inner rear pillar (RH & LH)
15. Inner rear pillar reinforcement (RH &
LH)
16. Outer rear wheelhouse (RH & LH)
17. Upper outer rear wheelhouse exten-
sion (RH & LH)
18. Lower outer rear wheelhouse exten-
sion (RH & LH)
19. Inner rear wheelhouse (RH & LH)
20. Roof
21. Front roof rail
22. Roof bow No. 2
23. Roof bow No. 3
24. Rear roof rail
25. Rear fender assembly (RH & LH)
26. Upper back pillar assembly (RH &
LH)
27. Lower back pillar assembly (RH &
LH)
28. Rear side bumper retainer (RH & LH) 29. Rear bumper stay reinforcement
30. Fuel filler lid
31. Rear panel assembly
32. Upper rear bumper retainer
33. Front door assembly (RH & LH)
34. Outer front door panel (RH & LH)
35. Rear door assembly (RH & LH)
36. Outer rear door panel (RH & LH)
37. Inner center front bumper reinforce-
ment
38. Inner center rear bumper reinforce-
ment
39. Rear bumper stay (RH & LH)
40. Outer rear wheelhouse reinforce-
ment (RH & LH)
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
*: Aluminum portion
CORROSION PROTECTION
BRM-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
CORROSION PROTECTION
Description
INFOID:0000000005248948
To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.
Anti-Corrosive Precoated Steel (Galvannealed Steel)
To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet is adopted replacing conventional
zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.
NISSAN genuine parts are fabricated from galvannealed steel. Therefore, it is recommended that NISSAN
genuine parts or an equivalent be used for panel replacement to maintain the anti-corrosive performance built
into the vehicle at the factory.
Phosphate Coating Treatment and Cationic Electrodeposition Primer
A phosphate coating treatment and a cationic electrodeposition
primer, which provide excellent corrosion protection, are applied to
all body components.
CAUTION:
Confine paint removal during welding operation to an absolute
minimum.
NISSAN genuine parts are also treated in the same manner. Therefore, it is recommended that NISSAN gen-
uine parts or an equivalent be used for panel replacement to maintain anti-corrosive performance built into the
vehicle at the factory.
Undercoating
INFOID:0000000005248949
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.
Precautions in Undercoating
1.
Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).
2.
Do not undercoat the exhaust pipe or other parts which become hot.
3.
Do not undercoat rotating parts.
4.
Apply bitumen wax after applying undercoating.
5.
After putting seal on the vehicle, put undercoating on it.
SIIA2294E
PIIA0095E
BRM-12
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
: Undercoated portions
: Sealed portions
JSKIA0695ZZ
BODY SEALING
BRM-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
BODY SEALING
Body Sealing
INFOID:0000000005248950
The following figure shows the areas that are sealed at the factory. Sealant that is applied to these areas
should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant
and not to allow other unaffected parts to come into contact with the sealant.
: Vehicle front
: Sealed portions
JSKIA0696ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст