Infiniti FX35, FX50 (S51). Manual — part 192
AV
SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
AV-541
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION (TWIN MONITOR)]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
Description
INFOID:0000000005525412
• Around view monitor control unit supplies to the front camera, rear camera and side camera. And then it
superimpose the images from each camera and outputs then to the display unit.
• Superimpose the guiding lines, predicted course line and sonar indicator to the camera image that outputs to
the front display unit.
• Around view monitor control unit performs the reception/transmission of communication signal with each
camera.
Diagnosis Procedure
INFOID:0000000005474908
1.
CHECK CONTINUITY SIDE CAMERA RH POWER SUPPLY AND GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect control unit connector and door mirror (passenger side) connector.
3.
Check continuity between around view monitor control unit harness connector and door mirror (passenger
side) harness connector.
4.
Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE SIDE CAMERA RH POWER SUPPLY
1.
Connect around view monitor control unit connector and door mirror (passenger side) connector.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
.
3.
CHECK CONTINUITY SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector and door mirror (passenger side) connector.
3.
Check continuity between around view monitor control unit harness connector and door mirror (passenger
side) harness connector.
Around view monitor control
unit
Door mirror
(passenger side)
Continuity
Connector
Terminals
Connector
Terminals
B46
32
D33
18
Existed
34
6
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
B46
34
Not existed
(+)
(
−
)
Condition
Voltage
(Approx.)
Around view monitor control
unit
Connector
Terminal
B46
34
Ground
“CAMERA” switch is ON or
shift position is “R”.
6.0 V
AV-542
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION (TWIN MONITOR)]
SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
4.
Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK SIDE CAMERA RH IMAGE SIGNAL
1.
Connect around view monitor control unit connector and door mirror (passenger side) connector.
2.
Turn ignition switch ON.
3.
Check signal between around view monitor control unit harness connector.
Is inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
.
NO
>> Replace side camera RH. Refer to
Around view monitor control
unit
Door mirror
(passenger side)
Continuity
Connector
Terminals
Connector
Terminals
B46
29
D33
5
Existed
30
17
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
B46
29, 30
Not existed
(+)
(
−
)
Condition
Reference value
Around view monitor control
unit
Around view monitor control
unit
Connector
Terminal
Connector
Terminal
B46
29
B46
30
“CAMERA” switch is ON or
shift position is “R”.
JSNIA0834GB
AV
STEERING SWITCH SIGNAL A CIRCUIT
AV-543
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION (TWIN MONITOR)]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH SIGNAL A CIRCUIT
Description
INFOID:0000000005474911
Transmits the steering switch signal to AV control unit.
Diagnosis Procedure
INFOID:0000000005474912
1.
CHECK STEERING SWITCH SIGNAL A CIRCUIT
1.
Disconnect AV control unit connector and spiral cable connector.
2.
Check continuity between AV control unit harness connector and spiral cable harness connector.
3.
Check continuity between AV control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SPIRAL CABLE
Check spiral cable.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace spiral cable. Refer to
.
3.
CHECK AV CONTROL UNIT VOLTAGE
1.
Connect AV control unit connector and spiral cable connector.
2.
Turn ignition switch ON.
3.
Check voltage between AV control unit harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace AV control unit. Refer to
4.
CHECK STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Check steering switch. Refer to
AV-543, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering switch. Refer to
Component Inspection
INFOID:0000000005474913
Measure the resistance between the steering switch connector terminals 14 to 17 and 15 to 17.
AV control unit
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M208
6
M36
24
Existed
AV control unit
Ground
Continuity
Connector
Terminal
M208
6
Not existed
(+)
(
−
)
Voltage
(Approx.)
AV control unit
AV control unit
Connector
Terminal
Connector
Terminal
M208
6
M208
15
5.0 V
AV-544
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION (TWIN MONITOR)]
STEERING SWITCH SIGNAL A CIRCUIT
Standard
Between terminals 14 and 17
ENTER switch ON
: 2003 – 2043
Ω
switch ON
: 716 – 730
Ω
MENU DOWN switch ON
: 318 – 324
Ω
MENU UP switch ON
: 120 – 122
Ω
SOURCE switch ON
: 0
Ω
Between terminals 15 and 17
switch ON
: 716 – 730
Ω
switch ON
: 318 – 324
Ω
VOL UP switch ON
: 120 – 122
Ω
VOL DOWN switch ON
: 0
Ω
JSNIA0112GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст