Infiniti FX35, FX50 (S51). Manual — part 482
INTEGRATED HOMELINK TRANSMITTER
DLK-51
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTEGRATED HOMELINK TRANSMITTER
Component Description
INFOID:0000000005239516
Item
Function
Homelink universal transceiver
A maximum of 3 radio signals can be stored and transmitted to operate the garage door, etc.
DLK-52
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000005239517
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following iteme for all sub system selection items.
×
: Applicable item
NOTE:
• *1:For models with Intelligent Key system this item is displayed, but is not used.
• *2: This item is displayed, but is not used.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
ECU Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT*
1
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
DIAGNOSIS SYSTEM (BCM)
DLK-53
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FREEZE FRAME DATA (FFD) AND IGN COUNTER
Freeze Frame Data
The BCM records the following condition at the moment a particular DTC is detected.
• Vehicle Speed
• Odo/Trip Meter
• Vehicle Condition (BCM detected condition)
IGN Counter
IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected.
• The number is 0 when a malfunction is detected.
• The number increases from 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition
switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)
INFOID:0000000005239518
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
WORK SUPPORT
CONSULT screen terms
Description
SLEEP>LOCK
While turning BCM status from low power consumption mode to normal mode (Power supply
position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to normal mode (Power supply
position is “OFF”)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle is stopping and selector
lever is not in the P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN” (From cranking up the en-
gine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emergency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply position is “OFF”) to low power
consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply position is “LOCK”) to low power
consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steering is locked)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering is unlocked)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
DLK-54
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000005239519
WORK SUPPORT
Monitor item
Description
DOOR LOCK-UNLOCK SET
Selective unlock function mode can be changed to operate (WITH) or not operate (WITHOUT) with
this mode.
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode.
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE: All doors are locked when shifting the selector lever from P position to other than the
P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode.
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode.
• Off: non-operational
• Unlock Only: door unlock operation only
• Lock Only: door lock operation only
• Lock/Unlock: lock/unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicated [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicated [ON/OFF] condition of back door request switch.
DOOR SW-DR
Indicated [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicated [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicated [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicated [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicated [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicated [ON/OFF] condition of lock signal from door lock unlock switch.
CDL UNLOCK SW
Indicated [ON/OFF] condition of unlock signal from door lock unlock switch.
KEY CYL LK-SW
Indicated [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicated [ON/OFF] condition of unlock signal from door key cylinder.
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation.
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched.
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched.
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III screen
is touched.
• The door lock actuator (rear LH and RH) is unlocked when “OTR ULK” on CONSULT-III screen
is touched.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст