Infiniti FX35, FX50 (S51). Manual — part 1117
PREPARATION
GW-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005235075
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000005235076
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Suction lifter
Holding the door glass
Remover tools
Removes the clips, pawls and metal clips
SIIA0995E
PIIB1805J
PIIB7923J
GW-10
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
REMOVAL AND INSTALLATION
WINDSHIELD GLASS
Exploded View
INFOID:0000000005235077
1.
Windshield molding
2.
Clip
3.
Windshield glass
4.
Insulator
5.
Dam sealant rubber (upper, lower)
6.
Rain sensor bracket
7.
Mirror base
8.
Primer
9.
Roof side molding
10.
Dash upper cross member
11.
Cowl top cover
12. Roof panel
13.
Adhesive
14. Front pillar outer upper
15. Front pillar garnish
16.
Body side outer
17. Front fender cover
18. Roof side molding fastener
: Clip
Unit:
mm (in)
Refer to
for symbols in the figure.
JMKIA2555GB
WINDSHIELD GLASS
GW-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000005235078
REMOVAL
1.
Remove front pillar garnishes (LH/RH). Refer to
INT-17, "Removal and Installation"
2.
Remove partially the headlining (front edge). Refer to
INT-24, "Removal and Installation"
3.
Remove front wiper arms (LH/RH). Refer to
WW-120, "Removal and Installation"
4.
Remove front fender covers (LH/RH). Refer to
DLK-245, "Removal and Installation"
.
5.
Remove cowl top covers (LH/RH). Refer to
EXT-23, "Removal and Installation"
6.
Remove roof side moldings (LH/RH). Refer to
EXT-37, "Removal and Installation"
.
7.
Apply protective tape around the windshield glass to protect the painted surface from damage.
8.
Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B) after removing
moldings.
NOTE:
Mark the body and the glass with matching marks if the windshield glass is reused.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
• Never use a cutting knife or power cutting tool when the windshield glass is reused.
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam sealant rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-
nished with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
• The molding must be installed securely so that it is in position and leaves no clearance.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Perform adjustment of front wiper arms stop location. Refer to
.
• Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time increases under
lower temperature and lower humidity.
PIIB5779E
GW-12
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
Inspection
INFOID:0000000005235079
REPAIRING WATER LEAKAGE FOR WINDSHIELD
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the windshield area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст