Infiniti FX35, FX50 (S51). Manual — part 575
REAR PROPELLER SHAFT
DLN-135
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F-R-2VL107]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
Put matching marks (A) on propeller shaft rubber coupling and
transfer companion flange.
CAUTION:
For matching marks, use paint. Never damage propeller
shaft rubber coupling and transfer companion flange.
5.
Put matching marks (A) on propeller shaft rebro joint and final
drive companion flange.
CAUTION:
For matching marks, use paint. Never damage propeller
shaft rebro joint and final drive companion flange.
6.
Loosen mounting nuts (1) of center bearing mounting brackets
(upper/lower).
CAUTION:
Tighten mounting nuts temporarily.
7.
Remove propeller shaft assembly fixing bolts and nuts.
CAUTION:
Never remove the rubber coupling from the propeller shaft
assembly.
8.
Slightly separate the rubber coupling from transfer companion
flange.
CAUTION:
Never damage transfer companion flange and rubber coupling.
9.
Remove center bearing mounting bracket fixing nuts.
CAUTION:
• The angle (A) is the first axis rubber coupling (1) forms
with the transfer companion flange (2). Never bend rubber
coupling above the angle (A).
• Never damage grease seal (3).
• Never damage rubber coupling.
10. Remove propeller shaft assembly.
CAUTION:
If constant velocity joint was bent during propeller shaft assembly removal, installation, or trans-
portation, its boot may be damaged. Wrap boot interference area to metal part with shop cloth or
equivalent to protect boot from breakage.
11. Remove clip and center bearing mounting bracket (upper/lower).
INSTALLATION
Note the following, and install in the reverse order of removal.
JSDIA0814ZZ
JPDID0208ZZ
: Vehicle front
A
: 0 – 4
°
JPDID0187ZZ
JSDIA0137ZZ
DLN-136
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F-R-2VL107]
REAR PROPELLER SHAFT
• Install center bearing mounting bracket (upper) (1) with its arrow
mark (A) facing forward.
• Adjust position of center bearing mounting bracket (upper), center
bearing mounting bracket (lower) (2) sliding back and forth to pre-
vent play in thrust direction of center bearing insulator (3). Install
center bearing mounting bracket (upper/lower) to vehicle.
• Align matching marks (A) to install propeller shaft rubber coupling
and transfer companion flange.
• Align matching marks (A) to install propeller shaft rebro joint and
final drive companion flange.
CAUTION:
JSDIA0127ZZ
JSDIA0814ZZ
JPDID0208ZZ
REAR PROPELLER SHAFT
DLN-137
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F-R-2VL107]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Tighten mounting bolt and nut in the order shown in the fig-
ure.
• Avoid damaging the rebro joint boot, protect it with a shop
towel or equivalent.
• If propeller shaft or final drive has been replaced, connect them as
follows:
- Install the propeller shaft while aligning its matching mark (A) with
the matching mark (B) on the joint as close as possible.
• After assembly, perform a driving test to check propeller shaft
vibration. If vibration occurred, separate propeller shaft from final
drive. Reinstall companion flange after rotating it by 60, 120, 180,
240, 300 degrees. Then perform driving test and check propeller
shaft vibration again at each point.
CAUTION:
• The angle (A) is the first axis rubber coupling (1) forms with
the transfer companion flange (2). Never bend rubber cou-
pling above the angle (A).
• Never damage grease seal (3).
• Never damage rubber coupling.
Inspection
INFOID:0000000005249177
APPEARANCE
Check propeller shaft for bend and damage. If damage is detected, replace propeller shaft assembly.
PROPELLER SHAFT RUNOUT
Check propeller shaft runout at measuring points with a dial indica-
tor. If runout exceeds specifications, replace propeller shaft assem-
bly. For measuring point, refer to
.
CENTER BEARING
Check center bearing for noise and damage. If noise or damage is detected, replace propeller shaft assembly.
CAUTION:
JPDID0204ZZ
SDIA2049E
A
: 0 – 4
°
JSDIA0137ZZ
Limit
Propeller shaft runout
: Refer to
.
JSDIA0079ZZ
DLN-138
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F-R-2VL107]
REAR PROPELLER SHAFT
Never disassemble center bearing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст