Infiniti FX35, FX50 (S51). Manual — part 441
ENGINE COOLANT
CO-9
< PERIODIC MAINTENANCE >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
If contaminated, flush the engine cooling system. Refer to
.
Refilling
INFOID:0000000005246356
1.
Remove engine cover. Refer to
.
2.
Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to
3.
Check that each hose clamp is firmly tightened.
4.
Remove air relief plug (2) on radiator left side.
5.
Remove air relief plug (1) on heater hose. (models with air relief
plug on heater hose)
6.
Fill radiator, and reservoir tank if removed, to specified level.
• Pour engine coolant through engine coolant filler neck
slowly of less than 2 (2-1/8 US qt, 1-3/4 lmp qt) a minute
to allow air in system to escape.
• Use Genuine NISSAN Long Life Antifreeze/Coolant or an
equivalent mixed with water (distilled or demineralized).
Refer to
MA-12, "Fluids and Lubricants"
.
Tightening torque
: Refer to
1
: Reservoir tank
3
: Engine cover
: Vehicle front
JPBIA0260ZZ
2
: Heater hose
: Vehicle front
JPBIA0104ZZ
Engine coolant capacity
: Refer to
"Periodical Maintenanc
e Specification"
(With reservoir tank at
“MAX” level)
JPBIA0412ZZ
CO-10
< PERIODIC MAINTENANCE >
[VQ35HR]
ENGINE COOLANT
7.
When engine coolant overflows air relief hole on radiator, install air relief plug with new O-ring.
8.
Repeat step 6.
9.
When engine coolant overflows air relief hole on heater hose, install air relief plug with new O-ring. Then
refill radiator with engine coolant. (models with air relief plug on heater hose)
10. Install radiator cap.
11. Warm up engine until opening thermostat. Standard for warming-up time is approximately 10 minutes at
3,000 rpm.
• Check thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.
CAUTION:
Watch water temperature gauge so as not to overheat engine.
12. Stop the engine and cool down to less than approximately 50
°
C (122
°
F).
• Cool down using fan to reduce the time.
• If necessary, refill radiator up to filler neck with engine coolant.
13. Refill reservoir tank to “MAX” level line with engine coolant.
14. Repeat steps 10 through 13 two or more times with radiator cap installed until engine coolant level no
longer drops.
15. Check cooling system for leakage with engine running.
16. Warm up the engine, and check for sound of engine coolant flow while running engine from idle up to
3,000 rpm with heater temperature controller set at several position between “COOL” and “WARM”.
• Sound may be heard from the heater unit.
17. Repeat step 16 three times.
18. If sound is heard, bleed air from cooling system by repeating step 6, and steps from 10 to 17 until engine
coolant level no longer drops.
19. Check that the reservoir tank cap is tightened.
Flushing
INFOID:0000000005246357
1.
Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to
Reservoir tank engine cool-
ant capacity
: Refer to
"Periodical Maintenanc
e Specification"
.
(At “MAX” level)
A
: MAX
B
: MIN
JPBIA0102ZZ
Tightening torque
: Refer to
.
: 1.2 N·m (0.12 kg-m, 11 in-lb)
Tightening torque
: Refer to
ENGINE COOLANT
CO-11
< PERIODIC MAINTENANCE >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
2.
Remove air relief plug (1) on heater hose. (models with air relief
plug on heater hose)
3.
Remove air relief plug (2) on radiator.
4.
Fill radiator with water until water spills from the air relief holes, then close air relief plugs. Fill radiator and
reservoir tank with water and reinstall radiator cap.
5.
Run the engine and warm it up to normal operating temperature.
6.
Rev the engine two or three times under no-load.
7.
Stop the engine and wait until it cools down.
8.
Drain water from the system. Refer to
.
9.
Repeat steps 1 through 8 until clear water begins to drain from radiator.
10. Check that the reservoir tank cap is tightened.
2
: Heater hose
: Vehicle front
JPBIA0104ZZ
1
: Reservoir tank
3
: Engine cover
: Vehicle front
JPBIA0260ZZ
Tightening torque
: Refer to
.
CO-12
< PERIODIC MAINTENANCE >
[VQ35HR]
RADIATOR
RADIATOR
RADIATOR CAP
RADIATOR CAP : Inspection
INFOID:0000000005246358
• Check valve seat of radiator cap.
- Check if valve seat (A) is swollen to the extent that the edge of the
metal plunger (B) cannot be seen when watching it vertically from
the top.
- Check if valve seat has no soil and damage.
• Pull negative-pressure valve to open it, and check that it close
completely when released.
- Check that there is no dirt or damage on the valve seat of radiator
cap negative-pressure valve.
- Check that there are no unusualness in the opening and closing
conditions of negative-pressure valve.
• Check radiator cap relief pressure.
- When connecting radiator cap to the radiator cap tester (commer-
cial service tool) and the radiator cap tester adapter (commercial
service tool) (A), apply engine coolant to the cap seal surface.
• Replace radiator cap if there is an unusualness related to the above three.
CAUTION:
When installing radiator cap, thoroughly wipe out the water outlet (front) filler neck to remove any
waxy residue or foreign material.
RADIATOR
RADIATOR : Inspection
INFOID:0000000005246359
Check radiator for mud or clogging. If necessary, clean radiator as per the following:
• Be careful not to bend or damage radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as radiator cooling fan assem-
bly and horns. Then tape harness and connectors to prevent water from entering.
1.
Apply water by hose to the back side of the radiator core vertically downward.
2.
Apply water again to all radiator core surfaces once per minute.
JPBIA0108ZZ
SMA967B
Standard and limit
: Refer to
JPBIA0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст