Infiniti FX35, FX50 (S51). Manual — part 21
ADP-76
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace seat memory switch. Refer to
ADP-217, "Removal and Installation"
.
Seat memory switch
Condition
Continuity
Terminal
4
1
Memory switch 1
Push
Existed
Release
Not existed
2
Memory switch 2
Push
Existed
Release
Not existed
3
Set switch
Push
Existed
Release
Not existed
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000005249708
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000005249709
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode using CON-
SULT-III.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
ADP-77, "CHANGEOVER SWITCH : Diagnosis Procedure"
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000005249710
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than the above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
M26
2
Ground
5
3
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M51
2
M26
3
Existed
18
2
ADP-78
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-216, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to
ADP-78, "CHANGEOVER SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (changeover switch). Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-36, "Intermittent Incident"
>> INSPECTION END
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000005249711
1.
CHECK CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-82, "Removal and Installation"
MIRROR SWITCH
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M51
2
Not existed
18
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
M26
13
Existed
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
M26
2
13
Changeover switch
LEFT
Existed
Other than above
Not existed
3
RIGHT
Existed
Other than above
Not existed
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MIRROR SWITCH : Description
INFOID:0000000005249712
It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.
MIRROR SWITCH : Component Function Check
INFOID:0000000005249713
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
using CONSULT-III.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
ADP-79, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000005249714
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
MIR CON SW-UP/DN
When operating the mirror switch toward the up or down side.
: ON
Other than the above.
: OFF
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than the above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
M26
4
Ground
5
5
6
14
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M51
3
M26
6
Existed
4
5
19
14
20
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст