Infiniti FX35, FX50 (S51). Manual — part 405

CCS-440

< BASIC INSPECTION >

[LDW & LDP]

DIAGNOSIS AND REPAIR WORK FLOW

KEY POINTS

• WHAT. . System and functions
• WHEN. . Date, Frequencies
• WHERE. . Road conditions
• HOW. . Operating conditions, Symptoms

WORK SHEET SAMPLE

JPOIA0203GB

CCS

PRE-INSPECTION FOR DIAGNOSIS

CCS-441

< BASIC INSPECTION >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

PRE-INSPECTION FOR DIAGNOSIS

Inspection Procedure

INFOID:0000000005502054

1.

CHECK CAMERA LENS AND WINDSHIELD

Are camera lens and windshield contaminated with foreign materials?

YES

>> Clean camera lens and windshield.

NO

>> GO TO 2.

2.

CHECK LANE CAMERA UNIT INSTALLATION CONDITION

Check lane camera unit installation condition (installation position, properly tightened, a bent bracket).
Is it properly installed?

YES

>> GO TO 3.

NO

>> Install lane camera unit properly, and perform camera aiming. Refer to

CCS-445, "CAMERA AIM-

ING ADJUSTMENT : Description"

.

3.

CHECK VEHICLE HEIGHT

Check vehicle height. Refer to

FSU-20, "Wheel Height"

(2WD) or

FSU-40, "Wheel Height"

(AWD).

Is vehicle height appropriate?

YES

>> INSPECTION END

NO

>> Repair vehicle to appropriate height.

CCS-442

< BASIC INSPECTION >

[LDW & LDP]

ACTION TEST

ACTION TEST

Description

INFOID:0000000005502055

• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.

WARNING:

Be careful of traffic conditions and safety around the vehicle when performing road test.

CAUTION:

• Fully understand the following items well before the road test;
- Precautions: Refer to

CCS-535, "Precaution for LDW/LDP System Service"

.

- System description for LDW: Refer to

CCS-451, "System Description"

.

- System description for LDP: Refer to

CCS-456, "System Description"

.

- Normal operating condition: Refer to

CCS-533, "Description"

.

Inspection Procedure

INFOID:0000000005502056

WARNING:

Be careful of traffic conditions and safety around the vehicle when performing road test.

CAUTION:

• Fully understand the following items well before the road test;
- Precautions: Refer to

CCS-535, "Precaution for LDW/LDP System Service"

.

- System description for LDW: Refer to

CCS-451, "System Description"

.

- System description for LDP: Refer to

CCS-456, "System Description"

.

- Normal operating condition: Refer to

CCS-533, "Description"

.

1.

ACTION TEST FOR LDW

1.

Drive the vehicle.

2.

Turn LDW switch ON (LDW ON indicator is ON).
NOTE:
LDP system is OFF.

3.

Check the LDW operation according to the following table.

>> GO TO 2.

2.

CHECK LDP SYSTEM SETTING

1.

Start the engine.

2.

Check that the LDP system setting can be enabled/disabled on the navigation screen.

3.

Turn OFF the ignition switch and wait for 5 seconds or more.

4.

Check that the previous setting is saved when the engine starts again.

Input

Output

Vehicle

speed

[km/h

(MPH)]

Vehicle condition/ Driver's oper-

ation

Action

LDW ON

indicator

Indication on the combination

meter

Buzzer

Less than

64 (40)

Close to lane marker

No action

ON

OFF

—

72 (45) or

more

Close to lane marker

Warning

• Buzzer sounds
• Warning lamp

blinks

ON

Short continu-

ous beeps

• Close to lane marker
• Turn signal ON (Deviate side)

No action

ON

OFF

—

JPOIA0018GB

CCS

ACTION TEST

CCS-443

< BASIC INSPECTION >

[LDW & LDP]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

>> GO TO 3.

3.

ACTION TEST FOR LDP

1.

Enable the setting of the LDP system on the navigation screen.

2.

Turn LDP switch ON (LDP ON indicator lamp is ON).
NOTE:
LDW system is OFF.

3.

Check the LDP operation according to the following table.

Input

Output

Vehicle speed

[km/h (MPH)]

Vehicle condition/ Driver's

operation

Action

Indication on the combination meter

Buzzer

Less than 64

(40)

Close to lane marker

No action

—

JPOIA0021GB