Infiniti FX35, FX50 (S51). Manual — part 1584
REAR SEAT BELT
SB-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
SEAT BELT RETRACTOR : Exploded View
INFOID:0000000005243356
SEAT BELT RETRACTOR : Removal and Installation
INFOID:0000000005243357
REMOVAL
1.
Remove the outer anchor.
• Remove the rear seat cushion. Refer to
SE-94, "Removal and Installation"
.
• Remove the outer anchor fixing anchor bolt, and then remove the outer anchor.
2.
Remove the inner anchor
1.
Retaining washer
2.
Spacer
3.
Shoulder anchor
4.
Anchor bolt
5.
Rear seat belt escutcheon
6.
Outer seat belt retractor
7.
Outer anchor
8.
Inner anchor
9.
Outer seat belt buckle
10. Center seat belt buckle
11.
Seat belt finisher
12. Seat belt guide (upper)
13. Seat belt guide (lower)
14. Center seat belt retractor cover
15. Anchor nut
16. Center seat belt retractor
17. Seat back frame
Refer to
JMHIA0706GB
SB-12
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
Remove the inner anchor fixing anchor bolt, and then remove the inner anchor.
3.
Remove the shoulder anchor.
• Remove the luggage side upper and lower finisher. Refer to
INT-29, "Removal and Installation"
• Remove the shoulder anchor fixing anchor bolt, and then remove the shoulder anchor.
4.
Remove the outer seat belt retractor.
• Remove the luggage side upper and lower finisher. Refer to
INT-29, "Removal and Installation"
• Remove the fixing anchor bolt, and then remove the outer seat belt retractor.
5.
Remove the center seat belt retractor.
• Remove rear seat cushion. Refer to
SE-94, "Removal and Installation"
.
• Remove rear center seat belt anchor bolt. Refer to
SB-11, "SEAT BELT RETRACTOR : Exploded View"
.
• Remove the pawls, and then remove seat belt finisher.
• Remove seatback board (RH). Refer to
SE-95, "Disassembly and Assembly"
• Disengage rear center seat belt retractor cover (1) fixing pawls.
• Remove rear center seat belt retractor fixing nut (A) with a
socket wrench (B).
: Pawl
JMHIA0562ZZ
: Pawl
JMHIA0737ZZ
JMHIA0738ZZ
REAR SEAT BELT
SB-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
• Remove rear center seat belt retractor (1) and retractor cover
simultaneously from rear seatback frame.
• Remove hog rings (A) from seatback upper side.
• Remove seat belt guide (upper) fixing screws (A), and then
remove seat belt guide (upper) (1).
• Remove rear center seat belt assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Push the center seat belt webbing (1) to place center seat belt
webbing between seatback (RH) and reclining device inner
cover (not in front of LATCH striker) as shown in the figure,
before installing seat cushion.
SEAT BELT BUCKLE
SEAT BELT BUCKLE : Inspection
INFOID:0000000005243358
AFTER A COLLISION
WARNING:
JMHIA0739ZZ
JMHIA0740ZZ
JMHIA0741ZZ
JMHIA0797ZZ
SB-14
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
Inspect all seat belt assemblies including retractors and attached hardware after any collision.
NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced
unless the collision is minor and the belts show no damage and continue to operate normally. If not to
do so could result in serious personal injury in an accident. Seat belt assemblies not in use during a
collision should also be replaced if either damage or improper operation is noted. Seat belt pre-ten-
sioners should be replaced even if the seat belts are not in use during a frontal collision in which the
air bags are deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt is in use at the time of a collision (except for minor collisions and the belts, retractors, and
buckles show no damage and continue to operate normally).
• The seat belt is damaged in an accident. (i.e. torn webbing, bent retractor, or guide, etc.)
• The seat belt attaching point is damaged in an accident. Inspect the seat belt attaching area for damage or
distortion and repair if necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in
which the air bags are deployed.
PRELIMINARY CHECKS
1.
Check that the seat belt retractor, seat belt anchor, and buckle bolts are tightened firmly.
2.
Repeat the step above if necessary to check the other seat belts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст