Infiniti FX35, FX50 (S51). Manual — part 703
P0550 PSP SENSOR
EC-353
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> INSPECTION END
NO
>> Replace power steering pressure sensor.
EC-354
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P0603 ECM POWER SUPPLY
P0603 ECM POWER SUPPLY
Description
INFOID:0000000005236941
Battery voltage is supplied to the ECM even when the ignition switch
is turned OFF for the ECM memory function of the DTC memory, the
air-fuel ratio feedback compensation value memory, the idle air vol-
ume learning value memory, etc.
DTC Logic
INFOID:0000000005236942
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 second.
2.
Turn ignition switch OFF, wait at least 5 minutes.
3.
Turn ignition switch ON and wait at least 10 second.
4.
Repeat steps 2 and 3 for 5 times.
5.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005236943
1.
CHECK ECM POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the voltage between ECM harness connector terminals under the following conditions.
JMBIA0057ZZ
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0603
ECM power supply cir-
cuit
ECM back up RAM system does not function
properly.
• Harness or connectors
[ECM power supply (back up) circuit is
open or shorted.]
• ECM
P0603 ECM POWER SUPPLY
EC-355
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E3, F1
• 15 A fuse (No. 50)
• IPDM E/R harness connector E7
• Harness for open or short between ECM and battery
>> Repair or replace harness or connectors.
3.
CHECK INTERMITTENT INCIDENT
GI-36, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC Confirmation Procedure.
See
.
Is the 1st trip DTC P0603 displayed again?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-23, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> INSPECTION END
ECM
Voltage
+
–
Connector
Terminal
Connector
Terminal
F102
93
M107
128
Battery voltage
EC-356
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P0605 ECM
P0605 ECM
Description
INFOID:0000000005236944
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000005236945
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn it ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Turn ignition switch ON and wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn it ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
JMBIA0057ZZ
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст