Infiniti FX35, FX50 (S51). Manual — part 709
P1225, P1234 TP SENSOR
EC-377
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1225, P1234 TP SENSOR
Description
INFOID:0000000005236970
Electric throttle control actuator consists of throttle control motor,
throttle position (TP) sensor, etc. The throttle position sensor
responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
DTC Logic
INFOID:0000000005236971
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005236972
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct.
PBIB0145E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1225
Closed throttle position learning per-
formance (bank 1)
Closed throttle position learning value
is excessively low.
• Electric throttle control actuator
[Throttle position (TP) sensor 1 and
2]
P1234
Closed throttle position learning per-
formance (bank 2)
EC-378
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P1225, P1234 TP SENSOR
3.
Check if foreign matter is caught between the throttle valve (1)
and the housing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace malfunctioning electric throttle control actuator.
2.
Go to
EC-378, "Special Repair Requirement"
.
>> INSPECTION END
Special Repair Requirement
INFOID:0000000005236973
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-25, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-25, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
JMBIA1511ZZ
P1226, P1235 TP SENSOR
EC-379
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1226, P1235 TP SENSOR
Description
INFOID:0000000005236974
Electric throttle control actuator consists of throttle control motor,
throttle position (TP) sensor, etc. The throttle position sensor
responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
DTC Logic
INFOID:0000000005236975
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Repeat steps 2 and 3 for 32 times.
5.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005236976
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct.
PBIB0145E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1226
Closed throttle position learn-
ing performance (bank 1)
Closed throttle position learning is not performed
successfully, repeatedly.
• Electric throttle control actuator
[Throttle position (TP) sensor 1
and 2]
P1235
Closed throttle position learn-
ing performance (bank 2)
EC-380
< DTC/CIRCUIT DIAGNOSIS >
[VQ35HR]
P1226, P1235 TP SENSOR
3.
Check if foreign matter is caught between the throttle valve (1)
and the housing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace malfunctioning electric throttle control actuator.
2.
Go to
EC-380, "Special Repair Requirement"
.
>> INSPECTION END
Special Repair Requirement
INFOID:0000000005236977
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-25, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-25, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
JMBIA1511ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст