Infiniti F50. Manual — part 532
AIR CLEANER AND AIR DUCT
EM-15
C
D
E
F
G
H
I
J
K
L
M
A
EM
AIR CLEANER AND AIR DUCT
PFP:16500
Removal and Installation
EBS001JW
REMOVAL
1.
Remove engine cover and air cleaner cover. Refer to
EM-11, "Removal and Installation"
.
2.
Remove harness connector from mass air flow sensor.
3.
Remove air duct (inlet), air cleaner case/mass air flow sensor assembly and air duct/resonator assembly
disconnecting their joints.
●
Add marks as necessary for easier installation.
4.
Remove mass air flow sensor from air cleaner case.
CAUTION:
Handle mass air flow sensor with following cares.
●
Do not shock it.
●
Do not disassemble it.
●
Do not touch its sensor.
5.
Remove resonator in fender lifting left fender protector.
INSTALLATION
Installation in the reverse order of removal paying attention to the following.
●
Align marks. Attach each joint. Screw clamps firmly.
SBIA0389E
1.
Air cleaner filter
2.
Holder
3.
O-ring
4.
Mass air flow sensor
5.
Vacuum hose
6.
Bracket
7.
Air duct
8.
Air duct (inlet)
9.
Air cleaner case
10.
Resonator
11.
Bracket
12.
Bracket
EM-16
AIR CLEANER AND AIR DUCT
CHANGING AIR CLEANER FILTER
1.
Remove air cleaner cover.
Refer to
EM-11, "Removal and Installation"
.
2.
Remove two clips and lift up air cleaner filter along with holder.
3.
Remove air cleaner filter from holder.
INTAKE MANIFOLD
EM-17
C
D
E
F
G
H
I
J
K
L
M
A
EM
INTAKE MANIFOLD
PFP:14003
Removal and Installation
EBS001L9
1.
PCV tube
2.
PCV hose
3.
EVAP canister purge control sole-
noid valve bracket
4.
EVAP canister purge control solenoid
valve
5.
EVAP hose
6.
EVAP tube
7.
Vacuum gallery
8.
Engine cover front bracket
9.
EVAP hose
PBIC2280E
EM-18
INTAKE MANIFOLD
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the engine coolant when the engine is hot.
1.
Remove engine cover (with power tool), air cleaner cover and battery cover. Refer to
.
2.
Release fuel pressure. Refer to
EC-48, "FUEL PRESSURE RELEASE"
3.
Remove air cleaner case and air duct assembly. Refer to
EM-15, "Removal and Installation"
4.
Drain engine coolant when engine is cooled. Refer to
CO-9, "Changing Engine Coolant"
.
5.
Disconnect fuel tube quick connector on engine side only.
●
Using tool of quick connector release [SST:J-45488], perform
the following steps to disconnect quick connector.
a.
Remove quick connector cap on engine side only.
b.
With the sleeve side of quick connector release facing quick
connector, install quick connector release onto fuel tube.
c.
Insert quick connector release into quick connector until sleeve
contacts and goes no further. Hold the quick connector release
on that position.
CAUTION:
Inserting the quick connector release hard will not discon-
nect quick connector. Hold quick connector release where
it contacts and goes no further.
d.
Draw and pull out quick connector straight from fuel tube.
CAUTION:
●
Pull quick connector holding A position in illustration.
●
Do not pull with lateral force applied. O-ring inside quick connector may be damaged.
●
Prepare container and cloth beforehand as fuel will leak out.
●
Avoid fire and sparks.
●
Be sure to cover openings of disconnected pipes with plug or plastic bag to avoid fuel leakage
and entry of foreign materials.
10. VIAS control solenoid valve
11. Water gallery
12. Gasket
13. Intake manifold lower
14. Water hose
15. Electric throttle control actuator
16. Intake manifold adapter
17. Engine cover rear bracket
18. Accelerator wire bracket
19. Intake manifold upper
20. Vacuum tank
21. Vacuum tank bracket
SBIA0353E
KBIA0702E
SBIA0354E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст