Infiniti F50. Manual — part 601
REAR WINDOW DEFOGGER
GW-75
C
D
E
F
G
H
J
K
L
M
A
B
GW
6.
CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1.
Connect door mirror defogger relay.
2.
Turn ignition switch ON.
3.
Check voltage between door mirror connector D2 (driver side) or D32 (passenger side) terminal 6 and
ground.
OK or NG
OK
>> INSPECTION END.
NG
>> Repair or replace harness between malfunction door
mirror and door mirror defogger relay.
Driver Side Door Mirror Defogger Circuit Check
EIS003T3
1.
CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between door mirror (driver side) connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness between door mirror defogger
relay and door mirror (driver side).
2.
CHECK DOOR MIRROR DEFOGGER GROUND HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (driver side) connector.
3.
Check continuity between driver side door mirror defogger connector D2 terminal 5 and ground.
OK or NG
OK
>> Check the following, if it is OK, replace door mirror
(driver side).
●
Check the condition of the harness and the connector.
●
Door mirror defogger firmament continuity check.
NG
>> Repair or replace harness between driver side door mir-
ror (driver side) and ground.
Connector
Terminals
(Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
D2
D32
6 (L/R)
Ground
Rear window defogger switch
ON
Battery
voltage
Rear window defogger switch
OFF
0
PIIA3521E
Con-
nector
Terminal
(Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
D2
6(L/R)
Ground
Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF.
0
PIIA3523E
5 (B) – Ground
: Continuity should exist.
PIIA3524E
GW-76
REAR WINDOW DEFOGGER
Passenger Side Door Mirror Defogger Circuit Check
EIS003T4
1.
CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between door mirror (passenger side) connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness between door mirror defogger
relay and door mirror (passenger side).
2.
CHECK DOOR MIRROR DEFOGGER GROUND HARNESS INSPECTION
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (passenger side) connector.
3.
Check continuity between door mirror (passenger side) connector D32 terminal 5 and ground.
OK or NG
OK
>> Check the following, if it is OK, replace door mirror pas-
senger side.
●
Check the condition of the harness and the connector.
●
Door mirror defogger firmament continuity check.
NG
>> Repair or replace harness between door mirror (passen-
ger side) and ground.
Filament Check
EIS003T5
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe.Then press the foil against the wire with your finder.
Con-
nector
Terminal
(Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
D32
6 (L/R)
Ground
Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF.
0
PIIA3525E
5 (B) – Ground
: Continuity should exist.
PIIA3526E
SEL122R
REAR WINDOW DEFOGGER
GW-77
C
D
E
F
G
H
J
K
L
M
A
B
GW
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament Repair
EIS003T6
REPAIR EQUIPMENT
●
Conductive silver composition (Dupont NO.4817 or equivalent)
●
Ruler 30 cm(11.8in) long
●
Drawing pen
●
Heat gun
●
Alcohol
●
Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm(0.20in)] of the break.
SEL263
SEL265
PIIA0215E
GW-78
REAR WINDOW DEFOGGER
4.
After repair has been completed, check repaired wire for conti-
nuity.This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun.A minimum dis-
tance of 3cm(1.2in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL012D
SEL013D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст