Infiniti F50. Manual — part 102
ON-VEHICLE SERVICE
AT-293
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
Connect terminal cord assembly connectors.
6.
Connect fluid temperature sensor 2 connector.
7.
Connect revolution sensor connector.
8.
Securely fasten terminal harness with clip.
9.
Install oil pan in transmission case.
a.
Install oil pan gasket in transmission case.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
SCIA2309E
SCIA2581E
SCIA2313E
SCIA2314E
AT-294
ON-VEHICLE SERVICE
b.
Install oil pan in transmission case.
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
CAUTION:
Do not reuse oil pan mounting bolts.
10. Install drain plug in oil pan.
CAUTION:
Do not reuse drain plug gasket.
11. Pour ATF into transmission assembly.
12. Connect heated oxygen sensor 2 harness connector.
13. Connect the negative battery terminal
SCIA2308E
: 6.9 - 8.8 N·m (0.71 - 0.89 kg-m, 61 - 77 in-lb)
: 29 - 39 N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
SCIA4113E
AIR BREATHER HOSE
AT-295
D
E
F
G
H
I
J
K
L
M
A
B
AT
AIR BREATHER HOSE
PFP:31098
Removal and Installation
ECS008A1
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, be careful not to be crushed or blocked by folding or bend-
ing the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend R portion.
●
When inserting a hose to the air breather tube, be sure to insert it fully until its end reaches the
tube spool portion.
PCIA0036E
AT-296
TRANSMISSION ASSEMBLY
TRANSMISSION ASSEMBLY
PFP:31020
Removal and Installation
ECS008A2
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1.
Disconnect the negative battery terminal.
2.
Remove engine under cover with power tool.
3.
Remove exhaust tube with power tool. Refer to
EX-3, "Removal and Installation"
4.
Remove propeller shaft. Refer to
PR-3, "Removal and Installation"
5.
Remove A/T control rod. Refer to
AT-282, "Adjustment of A/T Position"
6.
Disconnect A/T solenoid valve harness connectors.
7.
Remove crankshaft position sensor (POS) from A/T assembly.
8.
Remove fluid cooler tube and A/T fluid charging pipe.
9.
Plug up openings such as the fluid charging pipe hole, etc.
10. Remove air breather hose. Refer to
AT-295, "Removal and Installation"
11. Remove starter motor. Refer to
SC-28, "Removal and Installation"
1.
Transmission assembly
2.
A/T fluid charging pipe
3.
O-ring
4.
Fluid cooler tube
5.
Copper washer
6.
Bracket
7.
Engine rear member
8.
Insulator
9.
Fluid cooler hose
10. Hose band
SCIA1566E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст