Infiniti F50. Manual — part 407
DTC P0171, P0174 FUEL INJECTION SYSTEM FUNCTION
EC-269
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
EBS00MCP
1.
CHECK EXHAUST GAS LEAK
1.
Start engine and run it at idle.
2.
Listen for an exhaust gas leak before three way catalyst (manifold).
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace.
2.
CHECK FOR INTAKE AIR LEAK
1.
Listen for an intake air leak after the mass air flow sensor.
2.
Check PCV hose connection.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace.
SEC502D
EC-270
DTC P0171, P0174 FUEL INJECTION SYSTEM FUNCTION
3.
CHECK HEATED OXYGEN SENSOR 1 CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch “OFF”.
2.
Disconnect corresponding heated oxygen sensor 1 (HO2S1) harness connector.
3.
Disconnect ECM harness connector.
4.
Check harness continuity between ECM terminal and HO2S1 terminal as follows.
Refer to Wiring Diagram.
5.
Check harness continuity between the following terminals and ground.
Refer to Wiring Diagram.
6.
Check harness continuity between HO2S1 terminal 4 and engine ground.
7.
Also check harness for short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness for open or short between ECM and HO2S1
●
Harness for open or short between HO2S1 and engine ground
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK FUEL PRESSURE
1.
Release fuel pressure to zero. Refer to
EC-48, "FUEL PRESSURE RELEASE"
2.
Install fuel pressure gauge and check fuel pressure. Refer to
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
DTC
Terminals
Bank
ECM
Sensor
P0171
114
1
1
P0174
115
1
2
Continuity should exist.
DTC
Terminals
Bank
ECM
Sensor
P0171
114
1
1
P0174
115
1
2
Continuity should not exist.
Continuity should exist.
At idling: 350 kPa (3.57 kg/cm
2
, 51 psi)
DTC P0171, P0174 FUEL INJECTION SYSTEM FUNCTION
EC-271
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
DETECT MALFUNCTIONING PART
Check the following.
●
Fuel pump and circuit (Refer to
●
Fuel pressure regulator (Refer to
●
●
Fuel filter for clogging
>> Repair or replace.
7.
CHECK MASS AIR FLOW SENSOR
With CONSULT-II
1.
Install all removed parts.
2.
Check “MASS AIR FLOW” in “DATA MONITOR” mode with CONSULT-II.
With GST
1.
Install all removed parts.
2.
Check mass air flow sensor signal in MODE 1 with GST.
OK or NG
OK
>> GO TO 8.
NG
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
engine grounds. Refer to
EC-171, "DTC P0101 MAF SENSOR"
3.8 - 5.2 g·m/sec:
at idling
16.0 - 21.5 g·m/sec:
at 2,500 rpm
3.8 - 5.2 g·m/sec:
at idling
16.0 - 21.5 g·m/sec:
at 2,500 rpm
EC-272
DTC P0171, P0174 FUEL INJECTION SYSTEM FUNCTION
8.
CHECK FUNCTION OF INJECTORS
With CONSULT-II
1.
Start engine.
2.
Perform “POWER BALANCE” in “ACTIVE TEST” mode with
CONSULT-II.
3.
Make sure that each circuit produces a momentary engine
speed drop.
Without CONSULT-II
1.
Start engine.
2.
Listen to each injector operating sound.
OK or NG
OK
>> GO TO 9.
NG
>> Perform trouble diagnosis for “INJECTOR CIRCUIT”,
.
9.
CHECK INJECTOR
1.
Turn ignition switch “OFF”.
2.
Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
3.
Disconnect all injector harness connectors.
4.
Remove injector gallery assembly. Refer to
EM-31, "FUEL INJECTOR AND FUEL TUBE"
Keep fuel hose and all injectors connected to injector gallery.
5.
For DTC P0171, reconnect injector harness connectors on bank 1.
For DTC P0174, reconnect injector harness connectors on bank 2.
6.
Disconnect all ignition coil harness connectors.
7.
Prepare pans or saucers under each injector.
8.
Crank engine for about 3 seconds.
For DTC P0171, make sure that fuel sprays out from injectors
on bank 1.
For DTC P0174, make sure that fuel sprays out from injectors
on bank 2.
OK or NG
OK
>> GO TO 10.
NG
>> Replace injectors from which fuel does not spray out.
Always replace O-ring with new ones.
PBIB0133E
Clicking noise should be heard.
PBIB1986E
Fuel should be sprayed evenly for each injector.
PBIB1726E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст