Infiniti F50. Manual — part 558
DUAL MODE MUFFLER
EX-9
C
D
E
F
G
H
I
J
K
L
M
A
EX
INSPECTION OF DUAL MODE MUFFLER CONTROL UNIT OUTPUT SIGNAL
Check voltage between terminals 4 and 5 of dual mode muffler con-
trol unit harness connector and ground.
INSPECTION OF DUAL MODE MUFFLER CONTROL UNIT INPUT SIGNAL
Check voltage between terminals 1, 2, 3 and 6 of dual mode muffler
control unit harness connector and ground.
INSPECTION OF ECM OUTPUT SIGNAL
●
Check that tachometer operates normally.
●
Check voltage between ECM terminals 38, 113 and ground at
idling engine.
INSPECTION OF HARNESS CONTINUITY
Disconnect connectors of ECM, dual mode muffler control unit and
actuator. Check resistance between terminals.
Terminals
Input
signal
(Exhaust
control valve)
Condition
Voltage V
(+)
(-)
Terminal
(Wire color)
4 (G/Y)
GND
Open
ING ON
Battery voltage
(11 - 14)
0 - 1
5 (G/R)
Close
0 - 1
Battery voltage
(11 - 14)
PBIC0179E
Terminals
Input signal
Condition
Voltage V
(+)
(-)
Terminal (Wire color)
1 (W/G)
GND
Battery
ING ON
Battery voltage
(11 - 14)
3 (L)
Revolution
Idling
Approx. 4 - 6
2 (B)
Earth
IGN OFF
0
6 (R/Y)
Accelerator
pedal position
sensor opening
Over half
ING ON
More than
approx. 2.4
Below half
Approx. 0 - 2.4
PBIC0180E
Terminals
Output signal
Condition
Voltage V
(+)
(-)
Terminal (Wire color)
38 (W/G)
GND
Revolution
Idling
Approx. 4 - 6
113 (R/Y)
Accelerator
pedal position
sensor opening
Over half
IGN ON
More than
approx. 2.4
Below half
Approx. 0 - 2.4
PBIC0181E
Terminals (Wire color)
Resistance
Ω
Actuator terminal 1 (G/Y) and muffler control unit terminal 4 (G/Y)
0
Actuator terminal 2 (G/R) and muffler control unit terminal 5 (G/R)
ECM terminal 38 (W/G) and muffler control unit terminal 3 (L)
ECM terminal 113 (R/Y) and muffler control unit terminal 6 (R/Y)
PBIC0182E
EX-10
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Tightening torque
EBS001Z8
Unit: N·m (kg-m, ft-lb)
Unit: N·m (kg-m, in-lb)*
Exhaust system connections
Between exhaust manifold and exhaust front tube
Between exhaust front tube and center muffler
Between center muffler and main muffler
Exhaust mounting fixing bolts
For exhaust front tube
For center muffler
Heated oxygen sensor 2 (bank 1) (bank 2)
45.1 - 59.8 (4.6 - 6.1, 34 - 44)
51.0 - 64.7 (5.2 - 6.5, 38 - 47)
30.4 - 39.2 (3.1 - 4.0, 23 - 28)
25.5 - 31.4 (2.6 - 3.2, 19 - 23)
12.7 - 15.7 (1.3 - 1.6, 10 - 11)
40 - 50 (4.1 - 5.1, 30 - 36)
Dual mode muffler
Muffler control unit
Actuator
Actuator mounting bracket
Actuator cover
Cable lock nut (Both actuator and valve side)
Cable middle clamp tightening bolt
5.0 - 6.47 (0.51 - 0.65, 45 - 57)*
5.0 - 6.47 (0.51 - 0.65, 45 - 57)*
14.7 - 18.6 (1.5 - 1.8, 11 - 13)
5.0 - 6.47 (0.51 - 0.65, 45 - 57)*
25.5 - 33.3 (2.6 - 3.3, 19 - 24)
5.0 - 6.47 (0.51 - 0.65, 45 - 57)*
FAX-1
FRONT AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
A
B
FAX
FRONT AXLE
PREPARATION . . . . . . . . . . . . . . ... 2
Special Service Tools . . . . . . . . . . . ... 2
Commercial Service Tools . . . . . . . . . . 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 3
NVH Troubleshooting Chart . . . . . . . . . . 3
FRONT WHEEL HUB AND KNUCKLE . . . . . .. 4
On-Vehicle Inspection and Service . . . . . . .. 4
WHEEL BEARING INSPECTION . . . . . . . 4
Removal and Installation . . . . . . . . . . .. 4
Disassembly and Assembly . . . . . . . . . .. 6
DISASSEMBLY . . . . . . . . . . . . . . 6
ASSEMBLY . . . . . . . . . . . . . . ... 6
FAX-2
PREPARATION
PREPARATION
PFP:00002
Special Service Tools
EDS000WC
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
EDS000WD
Tool number
(Kent-Moore No.)
Tool name
Description
ST3623 0000
(J25840-A)
Sliding hammer
Removing wheel hub and bearing assembly
ZZA0803D
Tool name
Description
Power tool
●
Removing wheel nuts
●
Removing brake caliper assembly
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст