Infiniti F50. Manual — part 726
SIDE OIL SEAL
RFD-9
C
E
F
G
H
I
J
K
L
M
A
B
RFD
4.
Install the side flange with the following procedure.
a.
Attach the protector to side oil seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound which seems to affect the whole final drive.
5.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the illustration comes into the following, then
install the drive shaft.
6.
Align the installing position of the ABS wheel sensnor.Refer to
Tool number
: KV38107900 (J39352)
SDIA0822E
Measurement A
: Approx. 326 - 328 mm (12.83 - 12.91 in)
SDIA1039E
RFD-10
REAR FINAL DRIVE ASSEMBLY
REAR FINAL DRIVE ASSEMBLY
PFP:38300
Removal and Installation
EDS000YL
REMOVAL
1.
Remove exhaust center tube with power tool. Refer to
2.
Remove rear stabilizer bar with power tool. Refer to
3.
Remove rear propeller shaft from the final drive. Refer to
4.
Remove rear drive shaft from final drive. Then suspend it by wire etc. with power tool.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
7.
Place a transmission jack on the final drive.
CAUTION:
Do not place a transmission jack on the rear cover (aluminum case).
8.
Remove the mounting bolts and nuts connecting to the suspension member, and remove the rear final
drive.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installation, check the final drive oil level.
SDIA0774E
REAR FINAL DRIVE ASSEMBLY
RFD-11
C
E
F
G
H
I
J
K
L
M
A
B
RFD
Components
EDS000YM
R200 2–PINION
SDIA1173E
RFD-12
REAR FINAL DRIVE ASSEMBLY
Pre-Inspection
EDS000YN
Before disassembling final drive, perform the following inspection.
TOTAL PRELOAD
1.
Turn drive pinion in both directions several times to set bearing
rollers.
2.
Check total preload with Tool.
RING GEAR TO DRIVE PINION BACKLASH
Check ring gear to drive pinion backlash with a dial indicator at sev-
eral points.
RING GEAR RUNOUT
Check runout of ring gear with a dial indicator.
TOOTH CONTACT
1.
Drive pinion nut
2.
Companion flange (Rebro joint type) 3.
Front oil seal
4.
Pinion front bearing
5.
Pinion bearing adjusting spacer
(Collapsible spacer)
6.
Pinion rear bearing
7.
Pinion height adjusting washer
8.
Drive pinion
9.
Side oil seal
10. Ring gear
11.
Pinion mate shaft
12. Look pin
13. Pinion mate gear
14. Pinion mate thrust washer
15. Side gear
16. Side gear thrust washer
17. Differential case
18. Side bearing
19. Side bearing adjusting washer
20. Bearing cap
21. Rear cover
22. Filler plug
23. Drain plug
24. Gear carrier
25. Circular clip
26. Gasket
Tool number
: ST3127S000 (see J25765-A)
Total preload
: 2.84 - 3.75 N·m (0.29 - 0.38 kg-m, 26 -
33 in-lb)
SDIA1007E
Ring gear backlash:
0.10 - 0.15 mm (0.0039 - 0.0059 in)
SPD513
Runout limit:
0.05 mm (0.0020 in) less
SPD886
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст