Infiniti F50. Manual — part 230
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-167
C
D
E
F
G
H
J
K
L
M
A
B
BL
Preliminary Check
EIS003Q9
The system operation is canceled by turning ignition switch to “ACC” at any step between START and ARMED
in the following flow chart.
NOTE:
Before performing PRELIMINARY CHECK, disconnect IVCS unit connectors not to operate INFINITI commu-
nicator.
After performing preliminary check, go to symptom chart.
PIIA2861E
BL-168
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Symptom Chart
EIS003QA
*1: Make sure the system is in the armed phase.
PROCEDURE
Diagnostic procedure
SYMPTOM
1
Vehicle security
system cannot be
set by ····
All items
●
Door key cylinder
●
Electronic key
Diagnostic Procedure 1 (Check door, hood and trunk room lamp switch)
Refer to
BL-169, "Diagnostic Procedure 1"
Diagnostic Procedure 3 (Check door unlock sensor)
Refer to
BL-174, "Diagnostic Procedure 3"
Diagnostic Procedure 5 (Check trunk lid key unlock signal)
Refer to
BL-180, "Diagnostic Procedure 5"
Diagnostic Procedure 8 (Check ACC power supply)
Refer to
BL-184, "Diagnostic Procedure 8"
If the above systems are “OK”, replace BCM.
Door key cylinder
Diagnostic Procedure 4 (Check door key cylinder switch)
Refer to
BL-177, "Diagnostic Procedure 4"
If the above systems are “OK”, check driver door control unit (LCU01).
Security indicator does not turn “ON”.
Diagnostic Procedure 2 (Check security indicator lamp)
Refer to
BL-173, "Diagnostic Procedure 2"
If the above systems are “OK”, replace BCM.
2
*1
Vehicle security
system does not
alarm when ····
Any door is opened.
Diagnostic Procedure 1 (Check door, hood and trunk room lamp switch)
Refer to
BL-169, "Diagnostic Procedure 1"
If the above systems are “OK”, replace BCM.
Any door is unlocked without
using electronic key
Diagnostic Procedure 3 (Check door unlock sensor)
Refer to
BL-174, "Diagnostic Procedure 3"
If the above system is “OK”, check driver door control unit (LCU01) or door
control unit.
3
Vehicle security
alarm does not
activate.
Horn alarm
Diagnostic Procedure 6 (Check theft warning horn alarm)
Refer to
BL-181, "Diagnostic Procedure 6"
If the above systems are “OK”, check horn system.
Refer to
.
If the above systems are “OK”, replace BCM.
Headlamp alarm
Diagnostic Procedure 7 (Check headlamp alarm)
Refer to
BL-183, "Diagnostic Procedure 7"
If the above systems are “OK”, replace BCM.
4
Vehicle security
system cannot be
canceled by ····
Door key cylinder
Diagnostic Procedure 4 (Check door key cylinder switch)
Refer to
BL-177, "Diagnostic Procedure 4"
If the above systems are “OK”, check driver door control unit (LCU01).
Trunk lid key cylinder
Diagnostic Procedure 5 (Check trunk lid key cylinder switch)
Refer to
BL-180, "Diagnostic Procedure 5"
If the above systems are “OK”, replace BCM.
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-169
C
D
E
F
G
H
J
K
L
M
A
B
BL
Diagnostic Procedure 1
EIS003QB
1 – 1 CHECK FRONT DOOR SWITCH
1.
CHECK FRONT DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check front door switch (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check front door switch in “SWITCH MONITOR” mode.Refer to
.
OK or NG
OK
>> Front door switch is OK.
NG
>> GO TO 2
2.
CHECK FRONT DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect front door switch connector and BCM connector.
3.
Check continuity between front door switch connector B20 (driver), B220 (passenger) terminal 1 (W/R, W/
G) and BCM connector M4 (passenger), B4 (driver) terminal 37 (W/G), 142 (W/R).
4.
Check continuity between front door switch connector B20
(driver), B220 (passenger) terminal 1(W/R, W/G) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item
Condition
DOOR SW-DR
OPEN
: ON
CLOSE
: OFF
DOOR SW-AS
OPEN
: ON
CLOSE
: OFF
PIIA2464E
Driver side door switch
1 (W/R) – 142 (W/R)
: Continuity should exist.
Passenger side door switch
1 (W/G) – 37 (W/G)
: Continuity should exist.
Each door switches
1 (W/R, W/G) – Ground
: Continuity should not exist.
PIIA3118E
BL-170
VEHICLE SECURITY (THEFT WARNING) SYSTEM
3.
CHECK FRONT DOOR SWITCH
Check continuity between front door switch connector B20, B220 ter-
minal 1 and ground part of door switch.
OK or NG
OK
>> Check door switch case ground.
NG
>> Replace malfunction front door switch.
1 – 2 CHECK REAR DOOR SWITCH
1.
CHECK REAR DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check rear door switch (“DOOR SW-RR” and “DOOR SW-RL”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check front door switch in “SWITCH MONITOR” mode.Refer to
.
OK or NG
OK
>> Rear door switch is OK.
NG
>> GO TO 2
Terminal
Front door switch
Continuity
1
Ground part of
door switch
Pushed
NO
Released
YES
PIIA3351E
Monitor item
Condition
DOOR SW-RR
OPEN
: ON
CLOSE
: OFF
DOOR SW-RL
OPEN
: ON
CLOSE
: OFF
PIIA3117E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст