Infiniti F50. Manual — part 504
INJECTOR CIRCUIT
EC-657
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and body ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
EBS00MO4
1.
INSPECTION START
Turn ignition switch to “START”.
Is any cylinder ignited?
Yes or No
Yes
>> GO TO 2.
No
>> GO TO 3.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
6
13
15
17
L
P
B/R
G
Injector No. 2
Injector No. 4
Injector No. 6
Injector No. 8
[Engine is running]
●
Warm-up condition
●
Idle speed
NOTE:
The pulse cycle changes depending on rpm at idle.
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
BATTERY VOLTAGE
(11 - 14V)
PBIB0042E
PBIB0043E
EC-658
INJECTOR CIRCUIT
2.
CHECK OVERALL FUNCTION
With CONSULT-II
1.
Start engine.
2.
Perform “POWER BALANCE” in “ACTIVE TEST” mode with
CONSULT-II.
3.
Make sure that each circuit produces a momentary engine
speed drop.
Without CONSULT-II
1.
Start engine.
2.
Listen to each injector operating sound.
Clicking noise should be heard.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 3.
PBIB0133E
PBIB1986E
INJECTOR CIRCUIT
EC-659
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK INJECTOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch “OFF”.
2.
Disconnect harness connectors F21, F201 (bank 1) and harness connectors F41, F221 (bank 2).
3.
Turn ignition switch “ON”.
4.
Check voltage between harness connector F21 terminal 5 and
ground, harness connector F41 terminal 5 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E32, F32
●
Harness connectors F21, F201
●
Harness connectors F41, F221
●
Joint connector-19
●
Fuse block (J/B) No. 1 connector M1
●
Fuse block (J/B) No. 2 connectors M143, E215
●
15A fuse
●
Harness for open or short between harness connector F21 and fuse
●
Harness for open or short between harness connector F41 and fuse
>> Repair harness or connectors.
Voltage: Battery voltage
PBIB1252E
PBIB0180E
EC-660
INJECTOR CIRCUIT
5.
CHECK INJECTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch “OFF”.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between the following terminals. Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or shot to power in harness or connectors.
6.
CHECK SUB-HARNESS CIRCUIT FOR OPEN AND SHORT
1.
Disconnect injector harness connectors.
2.
Check harness continuity between the following terminals. Refer to Wiring Diagram.
OK or NG
OK
>> GO TO 7.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK INJECTOR
Refer to
EC-661, "Component Inspection"
OK or NG
OK
>> GO TO 9.
NG
>> Replace injector.
8.
CHECK INTERMITTENT INCIDENT
Refer to
EC-132, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Harness connector
Terminal
ECM terminal
F21
3
5
2
7
1
14
6
16
F41
3
6
2
13
1
15
6
17
Continuity should exist.
Harness connector
Terminal
Injector terminal
F21
5
1
1, 2, 3, 6
2
F41
5
1
1, 2, 3, 6
2
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст